Enigma2 Azbox HD v 1.0.21 for Elite/Premium

[Doctor Who]

Pre-announcement for loading Enigma 2 in AzBox HD Elite / Premium devices by USB Memory stick and this method is 100000% RISK FREE !!! As the new beta image will follow in next hour(s) .

Thanks to the the_ripper, telesat, Darezik and other people involved in this project.

If You want to load this version of Enigma 2 for AzBox HD Elite / Premium please follow this procedure :


1 . Load this patch.bin ( Enigma 2 ) file on FAT32 formatted USB Memory Stick


2. Turn Off Your AzBox HD Device, put USB Memory Stick inside and Turn on AzBox HD Device.


3. Follow the procedure USB Update on the screen, after process is finished, remove the USB stick from the AzBox HD Device, and let AzBox HD to Reboot


4. After reboot is finished, You should be in Enigma 2 AzBox HD Running state


5. If You tested enough Enigma 2 on AzBox HD Device and want to be back on AzBox Official Firmware, it is piece of cake


6. Load on FAT32 Formatted USB Memory stick patch.bin ( Official AzBox HD Firmware e.g 0.9.5020 ) .


7. Turn Off AzBox HD Device, put USB Memory stick in Receiver, and Turn it on.


8. On VFD You will see RESCUE MODE and IP Address will be listed.


9. On Your PC run application called AzUP by our team member telesat, enter IP of Your AzBox HD Device and click on UPDATE


10. Wait that Update is finished, and You will have again AzBox HD Official Firmware


This is totally RISK FREE Installation and Recovery procedure for AzBox HD Elite / Premium Devices !!!

Please, just follow procedure, and You will not have any problem at all, as this procedure was tested many many times internally by our team.

DOWNLOAD enigma2 v1.0.21

 

[Doctor Who]

all users are reporting this error

Appears "geeko :P" on the display and then appears the ip of the box.But everything stops there

Just reboot with the USB stick connected with the E2 firm, it should go into Recovery Mode, and show the IP on the VFD.

Launch AzUp and reinstall E2 firmware. Thats it!

 

[Doctor Who]

Updated installation procedure

...little (more) explanation about how to put e2 on azbox :

1. Load this patch.bin ( Enigma 2 ) file on FAT32 formatted USB Memory Stick
2. Turn Off Your AzBox HD Device, put USB Memory Stick inside and Turn on AzBox HD Device.
3. Follow the procedure USB Update on the screen, (patch version: 1.0.21 E2 by TheRipper, press OK, wait to finish, reboot - don't remove stick !)
4. Start AZUp , write IP adress of AZBox (see VFD), then click on Update button on AZUp, wait and follow message on AZUp and VFD, when all done - wait for reboot msg on VFD and then remove USB stick


btw, don't forget, this is not beta ver. of E2 , this is only test ver. because some people intentionally disparage this project and say : this is fake ...
and this is only presentation how tuner work and scann also.
please be a patient, soon, very soon beta ver of e2 with all function coming
but pls, I have a request to all of you, if you want E2 (fast to be ready) - pls don't distrb TheRipper and other and pls try to believe what we say , because , as in this case, only lose time in unnecessary debates
OK , i understand, always will be the provocateurs as Kanber , but pls You condemn their behavior

rgs,

 

[houarisat]

Enigma 2 for AzBox HD Elite

Enigma 2 for AzBox HD Elite

If You want to load this version of Enigma 2 for
AzBox HD Elite / Premium please follow this procedure :

1 . Load this patch.bin ( Enigma 2 ) file on FAT32 formatted USB 
Memory Stick


2. Turn Off Your AzBox HD Device, put USB Memory Stick inside 
and Turn on AzBox HD Device.


3. Follow the procedure USB Update on the screen, after process 
is finished, remove the USB stick from the AzBox HD Device, 
and let AzBox HD to Reboot


4. After reboot is finished, You should be in Enigma 2 AzBox HD 
Running state 


5. If You tested enough Enigma 2 on AzBox HD Device and want to 
be back on AzBox Official Firmware, it is piece of cake


6. Load on FAT32 Formatted USB Memory stick patch.bin ( Official 
AzBox HD Firmware e.g 0.9.5020 ) .


7. Turn Off AzBox HD Device, put USB Memory stick in Receiver, 
and Turn it on.


8. On VFD You will see RESCUE MODE and IP Address will be listed.


9. On Your PC run application called AzUP by our team member 
telesat, enter IP of Your AzBox HD Device and click on UPDATE


10. Wait that Update is finished, and You will have again AzBox HD 
Official Firmware


This is totally RISK FREE Installation and Recovery procedure for 
AzBox HD Elite / Premium Devices !!!

Please, just follow procedure, and You will not have any problem at .
all, as this procedure was tested many many times internally by our team.

Important: The installation of the image takes on its
own responsibility

Download image 44MB
​

 

[mohtadi]

Is it tested ?
Any reported bugs or failures ?

 

[testi]

it has no video/audio playback from tuner .... so this is not useable for normal users , this release is for testing purpose only ...wait for the next release.

 

[Doctor Who]

@all
I uploaded new em8634dvb.ko file. Pls replace old one from /lib/modules/2.6.22.19-19-the_ripper/extra/.
There is bootup file too, replace it from /etc/init.d, so you can activate showiframe bootlogo.

Reboot pls.

I started writing down changes.txt for DVB driver.

DOWNLOAD Driver

 

[Doctor Who]

tutorial how to make E2 on Premium +

For all members which own, AzBox HD Premium+ here is tutorial how to make E2 test running on their STB.

So, use standard procedure, to load E2 in Premium+, same as Elite/Premium.

Now, reboot Yout STB with usb memory stick in it with patch.bin file on it, just to enter in RECOVERY MODE, to obtain IP Address of Your receiver.

When You noted IP address of AzBox HD Premium+ ( which You can also do by accessing Router of Your LAN ), remove USB Memory stick, and turn off and turn on AzBox HD Receiver, by the power switch on the back side.

When You got on VFD 100, Your box is up and running.

Use FTP to connect on IP address which You already noted, and go in /etc/init.d .

There, You will find file named as bootup.

Download and Edit it.

Inside of it You will find two lines :

# Elite and Premium
insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f PAL_BG -digital -f HDMI_720p50 -hdmi_chip SiI9030 0 14 15 100 0"
# Premium+
#insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f PAL_BG -digital -f HDMI_720p50 -hdmi_chip SiI9134 0 14 15 100 0"

Comment insmode line below # Elite/Premium with character #.

Uncomment insmod line below #Premium+ , save file and overwrite existing file on STB.

Now, switch off and switch on Your Premium+, and You should have GUI and everything on Your Premium+ .

The problem is just as Elite/Premium are using Sil9030 HDMI Chip, and Premium is using Sil9134 . So it is same procedure to get it working on AzBox Ultra HD.

 

[Doctor Who]

AzBox HD Web Interface v 1.0 by DDamir


AzBox HD Web Interface v 1.0 by DDamir

AzBox HD Web Interface v 1.0 by DDamir

This is ipkg, for automatic installation of Web Interface for Enigma 2 OE 1.6 AzBox HD.

NOTE: There is no need to do manual uninstall of WebIF, as this is done automatically by provided IPKG file.

Thanks to our team member DDamir

DOWNLOAD AzBox HD Web Interface v 1.0 by DDamir

 

[Doctor Who]

Video OK

Just small info for all of You...

the_ripper successfully got video from satellite on FTA channels

We will give more info after deep testing.

 

[biged]

Why hasn't he published a video?

 

[gorski]

http://www.sat-universe.com/showthread.php?t=182787

 

[biged]

it is not the same thing I asked before
that video you mentioned is old I was referring to the new update

 

[gorski]

That's the "new" one. The latest you can see on your TV, if you wanna test the Beta they put out, so no need for a video...

 

[biged]

I have already tested

 

[gorski]

So, why as?

Oh, wait, allegedly The_Ripper got the picture of FTA, with his E2 and the driver he messed with...

 

[kam2006]

in minutes azbox premuim was doing all the normal steps but he writes the ip in the facade but in fact I azup.exe we update does not restart and gives the following message
Other error-Unable to complete Ruquest

 

[Doctor Who]

Dear friends,

Here is video which shows FTA channels running on enigma 2 for AzBox HD devices.

Please dont ask about zapping speed and slowness on channels ( It is caused, as we leaved buffer size for video smaller, for testing purposes ).

Only thing left is Audio part to be implemented ( under the work ).

When that is finished, You can expect new ver of enigma 2 for test....

http://www.youtube.com/watch?v=ky3lyxodiLw

 

[gorski]

The guy is drunk...

 

[Boryans]

If it is new firmware, and works with the emulator, recording channels, good media players. Even ready to pay the authors firmware within reason of course. But the work, you must agree complicated. Thank you for your efforts.