#===================================================
# /etc/tuxbox/config/oscam.conf
#
# Prepared by PurpleHaze for Peter Pan Neverland 2.1
#===================================================
# main configuration
#-------------------
[global]
nice = -1
waitforcards = 0
preferlocalcards = 1
saveinithistory = 1
[monitor]
port = 988
aulow = 120
monlevel = 1
# web interface
#--------------
[webif]
httpport = 8888
httpuser = oscam
httppwd = oscam
httpallowed = 10.0.0.100
httprefresh = 10
# protocols
#----------
[dvbapi]
enabled = 1
au = 1
boxtype = coolstream
[cccam]
port = 12000
reshare = 4
version = 2.1.4
#===================================================
# /etc/tuxbox/config/oscam.server
#
# Prepared by PurpleHaze for Peter Pan Neverland 2.1
#===================================================
# Internal reader lower (or if the box has only one reader)
#----------------------------------------------------------
[reader]
label = lower
protocol = internal
device = /dev/sci0
enable = 0
group = 1
emmcache = 1,3,2
# For some *** cards like CAID 093E you might need the boxkey.
# Read the key from you original decoder and remove the last digit.
# Convert from DEC to HEX. If the result is only 7 digits you must
# add a zero in front. Insert the 8 digits below in stead of 00000000.
#boxid = 00000000
# Internal reader upper (boxes with two readers)
#-----------------------------------------------
[reader]
label = upper
protocol = internal
device = /dev/sci1
enable = 0
group = 1
emmcache = 1,3,2
# For some *** cards like CAID 093E you might need the boxkey.
# Read the key from you original decoder and remove the last digit.
# Convert from DEC to HEX. If the result is only 7 digits you must
# add a zero in front. Insert the 8 digits below in stead of 00000000.
#boxid = 00000000
# Smargo (mousemode)
# Set enable to 1 if connected to the box, 0 if not used
#--------------------------------------------------------
[reader]
label = smargo
protocol = mouse
device = /dev/ttyUSB0
enable = 0
group = 1
emmcache = 1,3,2
# For some *** cards like CAID 093E you might need the boxkey.
# Read the key from you original decoder and remove the last digit.
# Convert from DEC to HEX. If the result is only 7 digits you must
# add a zero in front. Insert the 8 digits below in stead of 00000000.
boxid = 000000
[reader]
label = ubuntu_server
enable = 1
protocol = cccam
device = 192.168.1.20,12000
account = cooly1,cooly2
#services =
inactivitytimeout = 1
#caid =
ident =
group = 1
ecmcache = 1
lb_weight = 100
cccversion = 2.1.4
cccmaxhops = 3
[reader]
label = dreams_server
enable = 1
protocol = cccam
device = 215.196.1.2,12000
account = xxxxx,xxxxxx
#services =
inactivitytimeout = 1
#caid =
ident =
group = 1
ecmcache = 1
lb_weight = 100
cccversion = 2.1.4
cccmaxhops = 3
[reader]
label = ballas_server
enable = 1
protocol = cccam
device = no-ip.com,30000
account = user,passwd
#services =
inactivitytimeout = 1
#caid =
ident =
group = 1
ecmcache = 1
lb_weight = 100
cccversion = 2.1.4
cccmaxhops = 3
#===================================================
# /etc/tuxbox/config/oscam.user
#
# Prepared by PurpleHaze for Peter Pan Neverland 2.1
#===================================================
[account]
# this user is also defined in the dvbapi-section
user = oscam
pwd = oscam
group = 1
au = 1
monlevel = 4
[account]
user = xxxx
pwd = xxxx
monlevel = 0
uniq = 1
group = 1
au = reader1
services = services1
betatunnel = 0300.FFFF:0100,0400.FFFF:0100
ident = 0100:000000
caid = 0100
# user for group 2 with monitor access, AU enabled
[account]
user = user2
pwd = password2
monlevel = 1
uniq = 0
group = 2
au = reader2
services = services2
ident = 0200:000000
caid = 0200
# user for group 2 without monitor access, AU disabled, account disabled
[account]
user = user3
pwd = password3
disabled = 1
group = 2
services = services2
ident = 0200:000000
caid = 0200
# user for group 3 without monitor access, only one connection possible, AU disabled, multiple idents
[account]
user = user4
pwd = password4
monlevel = 0
uniq = 1
group = 3
ident = 0300:000000,FFFFFF;0400:FFFFFF
caid = 0300
Ok try this config. They goes in /var/tuxbox/config, chmod 777, you have too use latest oscam.arm. Depeds on you startscript, oscam or oscam.arm I think on your Img. put it in /var/bin or /usr/bin, chmod 777.
If I do not remember wrong you can activate oscam form -menu-ng.settings. Reboot box.
( I use org.img.)
Latest oscam here:
http://www.sat-universe.com/showthread.php?p=719710#post719710