Power of Dream HD+ 9000 Images

[juli13]

05/06/2011


We are pleased to offer you a POD for HD and et9000 et5000 Clarke-Tech / Xtrend. Because the manufacturer does not provide for the time cdk official image is based on OpenPlant. It is slightly different from a dream or vuplus POD HD, but it is a POD HD

Original image from 05/06

DOWNLOAD

 

[tani1]

Power of Dream HD+ Image for ET-9000

09-06-2011

Changes:

- Updated plugin Cooltv Guide by Coolman
- Updated Enigma2

podhd-et9000

 

[tani1]

Power of Dream HD+ Image for ET-9000

19-06-2011

Changes:

Enigma2 : Here

Openembedded : Here

podhd-et9000

 

[tani1]

Power of Dream HD+ Image for ET-9000

29-06-2011

Changes:

Update new drivers:

-increase framebuffer acceleration memory size
-always downmix audio on analog outputs
-support /proc/stb/fp/was_timer_wakeup (needs frontpanel update)
-vcr scart detection fix
-vfd improvements
-vfd: support greek and cyrillic charsets
-vfd: support additional symbols (see /proc/stb/lcd/*)
-pcm playback improvements
-sci improvements

podhd-et9000

 

[tani1]

Power of Dream HD+ Image for ET-9000

13-07-2011

Changes:

- Update the version of Linux 2.6.31
- Updated Enigma2 and plugins

Download ==> podhd-et9000

 

[tani1]

Power of Dream HD+ Image for ET-9000

24-07-2011

Changes:

- Routine Update

Download ==> podhd-et9000

 

[tani1]

Power of Dream HD+ Image for ET-9000

14-08-2011

Changes:

Update card manager: TNTSat fix

Download ==> podhd-et9000

 

[tani1]

POD HD - OpenPli 2.0 - ET9000

17-08-2011

Changes:

- Updated drivers
- Vfd: cyrillic / greek charactermap Improvements
- Scart: fix slowblanking
- Alsa: fix pcm playback of high bit rate data
- Fix mute status of ac3 passthrough mode in
- Add 'use_advanced_remote
- Add ioctl HDMI-CEC

Download ==> podhd-et9000

 

[tani1]

19.08.20111

New Image by SandBox Team based on Openpli 2.1

ATTENTION:
- It is not possible to go from 2.0 to 2.1 by an updated online, it is mandatory to flash a 2.1 full
- This new image requires an update of the bootloader before it can be installed

Download ==> podhd-2.1-et9000

 

[tani1]

Power of Dream HD 2.1 - ET9000

21.08.2011

Changes:

- Changing the launch of the card manager. Can resolve the concerns of card that was not recognized at boot.

Download ==> podhd-2.1-et9000

 

[juli13]

27/08/2011

CAUTION: Changing the complete image management

Before: POD full image does not change when the updates, and install a demo with a POD to date, it falait load an image a little older and do the update

Now: the complete picture is updated POD also:

- To install a full POD: take the picture early in the thread, you are a day
- If you already have a good POD generation installed, ca does not change, just update it (Menu - Settings - Software Manager - Software update)

DOWNLOAD

 

[juli13]

Online update Power of Dream HD+ Image for ET9000 13/09/2011

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update

[B]Update of 13/09/2011
[/B]
- Update routine Enigma2/Openembedded
- Added in the DLC picons OpenPlant

 

[juli13]

Online update Power of Dream HD+ Image for ET9000 26/09/2011


Update drivers:

HDMI-CEC: address change signal with POLLPRI
sharpness-scaler: fixed 'neutral' value (middle of the scale)
-added video source viewport / clipping settings (/ proc / stb / VMPEG / [0-1] / clip_ *)

Update routine enigma2 ...

Note that sometimes the demo does not reboot itself at the end of the update, in this case to OFF / ON to interuptor

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update

 

[juli13]

Online update Power of Dream HD+ Image for ET9000 28/09/2011

et5000/et9000: Driver update

-tune speed improvements
-stc sync mode setting: /proc/stb/stc/[0,1]/sync
-dts audio ff/rewind/skip fix
-sci improvements
-timeshift detection (T/S vfd symbol)
-userspace timeshift symbol control (/proc/stb/lcd/symbol_timeshift, disables internal timeshift detection)
-fix pip with webbrowser combination

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update

 

[juli13]

Online update Power of Dream HD+ Image for ET9000 05/10/2011

- Modification of hypercam manager: the launch of enigmatic, verify that at least one local card is detected. If this is not the case, recovery hypercam. This should overcome the desire to hypercam etx000 on the launch.

- Changes introduced by OpenPlant etxx00 linux

-update routine Enigma2

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update

 

[juli13]

POD Image HD 2.1 ET9000 26/01/2012

[B]Updated from 26/01
[/B]
- Updated Card Manager version 2.17, fixes the concerns of the black screen updates this weekend.

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update

 

[juli13]

POD Image HD 2.1 ET9000 02/02/2012

[B]Update 02/02[/B]
 
- Update Manager map 2.18: support for HD channels on some maps csat.
- Provision in the DLC web interface OpenWeb: to install the current interface REMOVE BEFORE installing OpenWeb in plugins / extensions. Starting today PODHD the 'complete' automatically include OpenWeb instead of the old web interface after Dream.

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update

 

[hilton]

POD Image HD 2.1 ET9000 21/09/2012

- Update routine enigma
- Added BackupSuite Pedro Newbie in the DLC
- Added many Linux utilities in the DLC

To take the lastest update of POD Image just go to:[/code]

Menu - Settings - Software Manager - Software update

 

[juli13]

Power of Dreams HD + 3.0 Based on PLI

[B]Update of 30/06/2013




  Updates routine enigma and plugins

 

[juli13]

Power of Dreams HD+ 4.0 , goût OPli

We are pleased to introduce the new POD HD 4.0  28/08/2013

The upgrade from 3 to 4 can not be done online and requiers a flash image.
 Thank you for reading this post before installing

DOWNLOAD