Octagon SX88 V2 - which OSCAM config file?

[Hpavil]

Thank you for your help. Which is the emu one in the list? Is it the last one starting "label = emulator"? Do I need to put a line underneath that "enable = 1"?
Do I leave the others alone?

 

[EnoSat]

Thanks for your help but I'm still stuck. I've put the files given by Kegnkiwi in the "etc/tubox/config" folder. There are no other files there. I've re-booted the receiver but OSCAM is not working.
I've looked in the Webinterface . In the oscam.version table, the entry is "ConfigDir: . /"
Advice would be much appreciated.

If "ConfigDir: ./" appears, then the configuration directory is not defined in the startup script and oscam uses the default root directory,
you probably overwrote the startup script supplied by ViX-team, with some file from the Internet.
That's why you see a warning on the TV screen after starting that there is no configuration!

 

[EnoSat]

[reader]
label = EMU
protocol = emu
device = emulator
disablecrccws_only_for = 0E00:000000
caid = 0500,0604,0E00,1010,1801,2600,2602,2610,44A0
detect = cd
ident = 0500:000000,007400,007800,021110,023800;0604:000000;0E00:000000;1010:000000;1801:000000,001101,002111,007301;2600:000000;2602:000000;2610:000000;44A0:000000
group = 1
emmcache = 2,1,2,1
emu_auproviders = 0604:010200;0E00:000000;1010:000000;2610:000000

As it gradually dies, you can "rationalize" the EMU reader, whoever has access to the L/R LNB for 56-East can add stuff for 44A0

 

[EnoSat]

Thank you for your help. Which is the emu one in the list? Is it the last one starting "label = emulator"? Do I need to put a line underneath that "enable = 1"?
Do I leave the others alone?

default is
enable = 1 (it is not necessary to have in the file)
but
enable = 0 (it is necessary to have it in the file if you want not to use the reader, but not to delete it)

 

[Hpavil]

Could you confirm it's the last entry in the list which I should edit i.e. the one starting "label = emulator"? At present it is not enabled at all.
1. I assume that I need to put a line underneath that "enable = 1"
2. Do I leave the others entries alone?

 

[EnoSat]

it depends if oscam is compiled with or without emu

 

[Hpavil]

Many thanks to all. OSCAM installed and I've got the various files that I needed. I now need to set it up with matching readers.

 

[kegnkiwi]

Many thanks to all. OSCAM installed and I've got the various files that I needed. I now need to set it up with matching readers.

If you are just entering a server line either convert the c line to oscam or if the server people give you it as oscam already just paste it into oscam.server and you should be good to go.

 

[Hpavil]

Thanks for that.

A naive question - will that enable the constant.cw reader as well, or do I need to do something else to set it up?

 

[EnoSat]

constant.cw has its own protocol/reader, basically equivalent to EMU what concerns the Constant Control Word

 

[Hpavil]

Is this something I set up through the webinterface?

I can see that there is a table "reader general settings" there but mine has a lot of blanks.

 

[EnoSat]

only a line with the location of the file is needed

 

[Hpavil]

Thanks again.

For OSCAM, is it possible to set it up to read the files with keys (Oscam.srvid, Oscam.keys) without subscribing to a line?

 

[EnoSat]

these are internal oscam files and have nothing to do with C-line,N-line,...

 

[Hpavil]

Thanks. Can you tell me how to set up Oscam to read those internal files?

 

[EnoSat]

reads them automatically from the configuration directory