mgcamd priority

T

tuntamor

Registered
Messages
10
Hi
This is my mg_cfg:

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }

Why not working?
Often the priority is given to CCcam instead of newcamd
 
D

DKaftermath

Senior Member
Messages
320
tuntamor said:
Hi
This is my mg_cfg:

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }

Why not working?
Often the priority is given to CCcam instead of newcamd
Click to expand...

then try on 02

also there is more to the config than just that part

the main part is the box type

set it to 12 for DGS based image
set to 11 for E2 images
 
T

tuntamor

Registered
Messages
10
DKaftermath said:
then try on 02

also there is more to the config than just that part

the main part is the box type

set it to 12 for DGS based image
set to 11 for E2 images
Click to expand...

Thank you. The other part is ok (I use 11 for E2 images)and cam works.
I'll try to set 2 in P: but I wish newcamd (local card) had priority
 
B

Bro1

Senior Member
Messages
278
i havent a clue if this could work but cant u try this

# 02 newcamd, cccamd, camd3, gbox, radegast
 
M

markybrook

Senior Member
Messages
136
I've had mgcamd working with both E2 and DGS images in CCcam client mode. However it does not seem very stable to me. I'm sure future releases will be better.
 
T

tuntamor

Registered
Messages
10
markybrook said:
I've had mgcamd working with both E2 and DGS images in CCcam client mode. However it does not seem very stable to me. I'm sure future releases will be better.
Click to expand...

Ok, but the issue is another. For me emu work, but non the parameter P:
I'll try the solution of DKaftermath and Bro1 and I write a feedback
 
F

freck

Registered
Messages
39
Only last night I flashed Sifteam extreme image and d/l'd MGcamd from the server.G :{32} and B:{11} ftp cline to cccam.list and restart cam...job done and more stable than incubusCamd by far.
Freck
 
E

egholm

Registered
Messages
25
Hallo
Yes, with cccamd only, 32 is the correct G line,
but if you want to use cccamd and newcamd i think 33 is the correct G line,
but i can`t test it.
Best regads
 
T

tuntamor

Registered
Messages
10
I've try to set P: with 02 unsuccessfully.
I've try to set P: with 02 and "# 02 newcamd, cccamd, camd3, gbox, radegast" unsuccessfully.
I can not run the priority. I can not understand if I'm the only one having this problem?

I thank everyone but I think the responses received, that someone has not understood my problem. I repeat that the emu works perfectly, both with newcamd with cccam but the priorities are not met. I want to go first on the newcamd and only if it finds nothing should go on cccam.
In fact this option is called "# network shares priority" and the choice "00" should do exactly what I'm looking, or not?
The other options (B: , G: ) are ok

I'm sorry for my english, maybe I can not explain
 
E

egholm

Registered
Messages
25
Can you tell me you G line ?
if G line is not correct, P line dosn`t make any sense.
P {00} and G {33} is the setting for newcamd and cccamd
with newcamd as prefered .
Best regards
 
T

tuntamor

Registered
Messages
10
roni261980 said:
set it on priority.list for diverse CAID
Click to expand...

I tried this route but does not work. I write into priority.list
# use this caid first
X: ( 09 3B }

becouse I've a 093b and the other 0919 but does not work
I also like more network shares priority becouse I could have both I and the other 093b

egholm said:
Can you tell me you G line ?
if G line is not correct, P line dosn`t make any sense.
P {00} and G {33} is the setting for newcamd and cccamd
with newcamd as prefered .
Best regards
Click to expand...

G: is 33
(if I unplug the cable network, newcamd works)
 
D

donloko

Registered
Messages
36
this is my mg cam config
and working very wel
lovig it

# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 02 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 32 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 02 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 02 } username password

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 03 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 50 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 11 }

# map all 180x nagra caids to 1801
# default is 01
F: { 01 }


and mage mgcam 755
and put line in cccam.list like
in cccam.cfg it wil work
only thing had a few images where its not working on
so try difrent images
 
A

agi0206

Registered
Messages
2
tuntamor said:
No other idea?
Are the only one having this problem?
Click to expand...

I had this problem, but now I'm not using newcamd anymore (only mgcamd as CCcam client)

Maybe when using a replace.list file, it can solve your problem.
The more dificult is to write this file ....
example :
R: {{ sid } { caid } { provid } { ecmpid } { newcaid } { newprovid } { newecmpid }}

Regards...
 
You must log in or register to reply here.
Top