Hi,
As far as I am concern, Mgcamd 1.35 should load SoftCam.Key by default but this is not happening for me, it good to mention that my Receiver ( IPBox 91 HD with latest Sifteam Firmware based on DGS ) which does not have access to Internet so the only choise that I have is using SoftCam.Key
This the procedure that I went through.
First of all installed MgCamd 1.35 and then downloaded the latest SoftCam.Key from this topic and put here ( /var/keys ) and changed the whole files' permission in that directory to 755.
Unfortunately after all these effort nothing come out of it
This is my mg_cfg configuration ( apart from mg_cfg every other file copied without any changes ) and this this is my log file.
Since I am new to this concept I tried to put as much detail as I could to lessen the ambiguity of my case.
I really appreciate to tell me what should do now or what have I done wrong,
Thanks in Advance
As far as I am concern, Mgcamd 1.35 should load SoftCam.Key by default but this is not happening for me, it good to mention that my Receiver ( IPBox 91 HD with latest Sifteam Firmware based on DGS ) which does not have access to Internet so the only choise that I have is using SoftCam.Key
This the procedure that I went through.
First of all installed MgCamd 1.35 and then downloaded the latest SoftCam.Key from this topic and put here ( /var/keys ) and changed the whole files' permission in that directory to 755.
Unfortunately after all these effort nothing come out of it
This is my mg_cfg configuration ( apart from mg_cfg every other file copied without any changes ) and this this is my log file.
Code:
# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }
# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }
# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 02 }
# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 33 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 01 } 5 30
# network ecm timeout in seconds
K: { 01 }
# newcamd dead routes connect retry, sec
Q: { 60 }
# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password
# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 01 } 192.168.10.200 514
# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }
# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }
# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }
# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 12 }
# map all 180x nagra caids to 1801
# default is 01
F: { 01 }
Code:
Aug 01 10:57:55 192.168.10.30 tuxbox mgcamd v1.35 by mixvt (compiled Jan 20 2010 22:15:45)
Aug 01 10:57:55 192.168.10.30 [mg] Net:33:1:0:1s Show ecm:1, emm:1 Up:1 Au:2 Dir:0 Osd:no:80:0 Cache:7 Log:1:192.168.10.200:514 Reread:0
Aug 01 10:57:55 192.168.10.30 [mg] Ecm cache time: 15
Aug 01 10:57:55 192.168.10.30 Box type: openbox/stapi
Aug 01 10:57:55 192.168.10.30 Conax.Key error 2: No such file or directory
Aug 01 10:57:56 192.168.10.30 Keys readed
Aug 01 10:57:56 192.168.10.30 Conax.Key error 2: No such file or directory
Aug 01 10:57:56 192.168.10.30 [config] newcamd route = ipbox:127.0.0.1:10110 server cardserver
Aug 01 10:57:56 192.168.10.30 [config] newcamd route = ipbox:127.0.0.1:10010 server cardserver
Aug 01 10:57:56 192.168.10.30 newcamd keep alive: 300, incoming port: 0
Aug 01 10:57:56 192.168.10.30 [mgcam] emm thread started
Aug 01 10:57:56 192.168.10.30 [newcamd] Connecting to 127.0.0.1:10110...
Aug 01 10:57:56 192.168.10.30 [newcamd] Connecting to 127.0.0.1:10010...
Aug 01 10:57:56 192.168.10.30 [cccamd] My nodeID 50fe5c0b885f8910
Aug 01 10:57:56 192.168.10.30 [newcamd] Connection to 127.0.0.1:10110 failed (3ms)
Aug 01 10:57:56 192.168.10.30 [newcamd] Connection to 127.0.0.1:10010 failed (4ms)
Aug 01 10:57:56 192.168.10.30 [mg0] service 14C2 index 0 pmt pid 0 (1)
Aug 01 10:57:56 192.168.10.30 CaPID: 0x18CB ProvID: 000000
Aug 01 10:57:56 192.168.10.30 CaPID: 0x1CB3 ProvID: 000000
Aug 01 10:57:56 192.168.10.30 [mg0] network can't decode
Aug 01 10:57:56 192.168.10.30 [mg0] pid 0x18CB failed to decode.
Aug 01 10:57:56 192.168.10.30 [mg0] No irdeto key(s) found for id 0 keynr 00
Aug 01 10:57:56 192.168.10.30 [mg0] network can't decode
Aug 01 10:57:56 192.168.10.30 [mg0] No irdeto key(s) found for id 80 keynr 00
Aug 01 10:57:56 192.168.10.30 [mg0] network can't decode
Aug 01 10:57:56 192.168.10.30 [mg0] pid 0x1CB3 failed to decode.
Aug 01 10:57:57 192.168.10.30 [mgcamd] emm started
Aug 01 10:57:57 192.168.10.30 CaPID: 0x0604 ProvID: 000000
Aug 01 10:57:57 192.168.10.30 CaPID: 0x0605 ProvID: 000000
Aug 01 10:57:57 192.168.10.30 CaPID: 0x0604 ProvID: 000000
Aug 01 10:57:57 192.168.10.30 [mgcamd] emm stoppedSince I am new to this concept I tried to put as much detail as I could to lessen the ambiguity of my case.
I really appreciate to tell me what should do now or what have I done wrong,
Thanks in Advance
Last edited: