I have bought an new DM 520 and i have flashed the latest openatv file to DM 520. An error occoured but the button to reebot was active.
I have reeboted and box has the red light
Dreambox DM520
M0CZS
L2=1
LLMB=1
BrCfg=E30FB7C6
#@
BCM973625A0 CFE v15.3, Endian Mode: Little
Build Date: Fri Jun 24 16:38:03 2016 (
[email protected])
Copyright (C) Broadcom Corporation.
card if inited
Enabling NAND flash at CS2: A5U4GA31ATS(DEVICE ID=0xC8DC9095), ECC Level=4, Spar
e Area Size=16
MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256
CPU speed: 751MHz
DDR Frequency: 1061 MHz
DDR Mode: DDR3
Total memory(MEMC 0): 512MB
MEMC 0 DDR Width: 16
Boot Device: SPI
Total flash: 16MB
RTS VERSION: rts_hevc10_1067
ETH0_PHY: INT
ETH0_MDIO_MODE: 1
ETH0_SPEED: 100
ETH0_PHYADDR: 1
DM init finalization
yxml: processing file of 131072 bytes... succeeded!
no file loaded, create xml restoring default xml
loaded network params of: DHCP, 192.168.0.219, 255.255.255.0, 192.168.0.1
[1] type 3, dev nandflash0.kernel, loader elf, filesys raw, file , options
[2] type 3, dev flash0.kernel, loader elf, filesys raw, file , options
[3] type 1, dev eth0, loader elf, filesys tftp, file , options
[email protected] con
sole=ttyS0,1000000 root=/dev/nfs ip=dhcp
added 3 sources to autoboot list
init fp
Initializing USB.
CFE initialized.
found card in unknown state
ca valid!
***** DREAMBOX SSBL *****
Not interrupted yet, trying autoboot or rescue loader, hit any key in the next 5
00ms to cancel
Proceeding with autoboot.. You can try aborting with Ctrl+C
*** Autoboot: Trying device 'nandflash0.kernel' file (raw,elf)
Ethernet link is up: 100 Mbps Full-Duplex
Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:
Loading: 0x80001000/7448768 0x8071b8c0/240128 Entry address is 0x805af9b0
Closing network eth0
Starting program at 0x805af9b0
[ 0.232000] console [ttyS0] enabled, bootconsole disabled
[ 0.232000] console [ttyS0] enabled, bootconsole disabled
[ 0.236000] loop: module loaded
[ 0.237000] brcmstb_nand: NAND controller driver is loaded
[ 0.238000] tun: Universal TUN/TAP device driver, 1.6
[ 0.239000] tun: (C) 1999-2004 Max Krasnyansky <
[email protected]>
[ 0.361000] bcmgenet: configuring instance #0 for internal PHY
[ 0.381000] bcmgenet bcmgenet.0: (unregistered net_device): link down
[ 0.382000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.383000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[ 0.383000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus numbe
r 1
[ 0.415000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
[ 0.421000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[ 0.422000] hub 1-0:1.0: USB hub found
[ 0.422000] hub 1-0:1.0: 2 ports detected
[ 0.423000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.424000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[ 0.424000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus numbe
r 2
[ 0.425000] ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400
[ 0.491000] hub 2-0:1.0: USB hub found
[ 0.491000] hub 2-0:1.0: 2 ports detected
[ 0.492000] Initializing USB Mass Storage driver...
[ 0.493000] usbcore: registered new interface driver usb-storage
[ 0.494000] USB Mass Storage support registered.
[ 0.494000] i2c /dev entries driver
[ 0.495000] lirc_dev: IR Remote Control driver registered, major 253
[ 0.495000] usbcore: registered new interface driver btusb
[ 0.497000] TCP: cubic registered
[ 0.497000] NET: Registered protocol family 10
[ 0.499000] NET: Registered protocol family 17
[ 0.499000] Bluetooth: RFCOMM TTY layer initialized
[ 0.500000] Bluetooth: RFCOMM socket layer initialized
[ 0.501000] Bluetooth: RFCOMM ver 1.11
[ 0.501000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 0.502000] Bluetooth: BNEP filters: protocol multicast
[ 0.502000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 0.503000] L2TP core driver, V2.0
[ 0.503000] Registering the dns_resolver key type
[ 0.504000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor
[ 0.506000] EBI CS2: setting up NAND flash (primary)
[ 0.507000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xdc (Unknown NAND 5
12MiB 3,3V 8-bit)
[ 0.508000] brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B
OOB, 8-bit, BCH-4
[ 0.508000]
[ 0.510000] Bad block table found at page 262080, version 0x01
[ 0.511000] Bad block table found at page 262016, version 0x01
[ 0.512000] nand_read_bbt: bad block at 0x000019ce0000
[ 0.513000] Creating 3 MTD partitions on "brcmnand.0":
[ 0.514000] 0x000000000000-0x00001f500000 : "rootfs"
[ 0.516000] 0x000000000000-0x000020000000 : "entire_device"
[ 0.518000] 0x00001f500000-0x00001fa00000 : "kernel"
[ 0.520000] EBI CS0: setting up SPI flash
[ 0.520000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address
[ 0.521000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated
[ 0.522000] m25p80 spi0.0: found mx25l12805d, expected w25q128bv
[ 0.523000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.525000] UBI: attaching mtd0 to ubi0
[ 0.525000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 0.526000] UBI: logical eraseblock size: 126976 bytes
[ 0.527000] UBI: smallest flash I/O unit: 2048
[ 0.527000] UBI: VID header offset: 2048 (aligned 2048)
[ 0.528000] UBI: data offset: 4096
[ 3.680000] UBI: max. sequence number: 1397
[ 3.697000] UBI: attached mtd0 to ubi0
[ 3.697000] UBI: MTD device name: "rootfs"
[ 3.698000] UBI: MTD device size: 501 MiB
[ 3.698000] UBI: number of good PEBs: 4007
[ 3.699000] UBI: number of bad PEBs: 1
[ 3.699000] UBI: number of corrupted PEBs: 0
[ 3.700000] UBI: max. allowed volumes: 128
[ 3.700000] UBI: wear-leveling threshold: 4096
[ 3.701000] UBI: number of internal volumes: 1
[ 3.702000] UBI: number of user volumes: 1
[ 3.702000] UBI: available PEBs: 0
[ 3.703000] UBI: total number of reserved PEBs: 4007
[ 3.703000] UBI: number of PEBs reserved for bad PEB handling: 40
[ 3.704000] UBI: max/mean erase counter: 2/1
[ 3.704000] UBI: image sequence number: -2022897891
[ 3.705000] UBI: background thread "ubi_bgt0d" started, PID 53
[ 3.707000] ALSA device list:
[ 3.707000] No soundcards found.
[ 3.758000] UBIFS: recovery needed
[ 3.760000] UBI error: ubi_io_write: error -5 while writing 2048 bytes to PEB
1051:71680, written 0 bytes
[ 3.761000] UBI warning: ubi_eba_write_leb: failed to write data to PEB 1051
[ 3.762000] UBI: recover PEB 1051, move data to PEB 2417
[ 3.763000] UBI error: ubi_io_write: error -5 while writing 2048 bytes to PEB
2417:2048, written 0 bytes
[ 3.764000] UBI warning: recover_peb: failed to write to PEB 2417
[ 3.765000] UBI: try again
[ 3.765000] UBI: run torture test for PEB 2417
[ 3.766000] UBI: recover PEB 1051, move data to PEB 2418
[ 3.767000] UBI error: do_sync_erase: cannot erase PEB 2417, error -5
[ 3.767000] UBI error: ubi_io_write: error -5 while writing 2048 bytes to PEB
2418:2048, written 0 bytes
[ 3.767000] UBI warning: recover_peb: failed to write to PEB 2418
[ 3.767000] UBI: try again
[ 3.767000] UBI: recover PEB 1051, move data to PEB 2419
[ 3.768000] UBI error: ubi_io_write: error -5 while writing 2048 bytes to PEB
2419:2048, written 0 bytes
[ 3.768000] UBI warning: recover_peb: failed to write to PEB 2419
[ 3.768000] UBI: try again
[ 3.768000] UBI: recover PEB 1051, move data to PEB 2420
[ 3.768000] UBI error: ubi_io_write: error -5 while writing 2048 bytes to PEB
2420:2048, written 0 bytes
[ 3.768000] UBI warning: recover_peb: failed to write to PEB 2420
[ 3.768000] UBI warning: ubi_ro_mode: switch to read-only mode
[ 3.768000] UBIFS error (pid 1): ubifs_leb_write: writing 2048 bytes to LEB 1
:67584 failed, error -5
[ 3.768000] UBIFS warning (pid 1): ubifs_ro_mode: switched to read-only mode,
error -5
[ 3.768000] Call Trace:
[ 3.768000] [<805b24e4>] dump_stack+0x8/0x34
[ 3.768000] [<8020ee3c>] ubifs_leb_write+0xc4/0xcc
[ 3.768000] [<802159c0>] ubifs_write_master+0xd8/0x138
[ 3.768000] [<8020d06c>] ubifs_mount+0xfbc/0x1580
[ 3.768000] [<800d3a7c>] mount_fs+0x20/0xe4
[ 3.768000] [<800f0258>] vfs_kern_mount+0x58/0xf4
[ 3.768000] [<800f0c7c>] do_kern_mount+0x4c/0x124
[ 3.768000] [<800f2b04>] do_mount+0x448/0x7b0
[ 3.768000] [<800f3154>] sys_mount+0x94/0xe4
[ 3.768000] [<806def0c>] mount_block_root+0x148/0x2a8
[ 3.768000] [<806df2c4>] prepare_namespace+0xfc/0x224
[ 3.768000] [<806dec14>] kernel_init+0x258/0x260
[ 3.768000] [<8000614c>] kernel_thread_helper+0x10/0x18
[ 3.768000]
[ 3.785000] UBI error: erase_worker: failed to erase PEB 2417, error -5
[ 3.786000] UBI: mark PEB 2417 as bad
[ 3.786000] UBI error: ubi_io_mark_bad: read-only mode
[ 3.787000] UBI error: do_work: work failed with error code -30
[ 3.787000] UBI error: ubi_thread: ubi_bgt0d: work failed with error code -30
[ 3.794000] VFS: Cannot open root device "ubi0:dreambox-rootfs" or unknown-bl
ock(31,0): error -5
[ 3.795000] Please append a correct "root=" boot option; here are the availab
le partitions:
[ 3.796000] 1f00 513024 mtdblock0 (driver?)
[ 3.796000] 1f01 524288 mtdblock1 (driver?)
[ 3.797000] 1f02 5120 mtdblock2 (driver?)
[ 3.797000] 1f03 16384 mtdblock3 (driver?)
[ 3.798000] 1f04 491412 mtdblock4 (driver?)
[ 3.799000] Kernel panic - not syncing: VFS: Unable to mount root fs on unkno
wn-block(31,0)
[ 3.800000] Rebooting in 180 seconds..
