E2 0n hardrive help

B

Bro1

Registered
Messages
278
i put nlb image on flash then put on the multiboot config aswell.unpacked E2 to hardrive using these commands

cd /media
tar zxvf 9000_usb.tar.gz


it unpacked ok so i typed sync

when i reboot box and press 6 nothing happens,it stays on booting.any idea where i have goen wrong

thanks

i used this e2 image http://www.sat-universe.com/showthread.php?t=153262
 
P

Pogifej

Registered
Messages
10
Hi!

I have 91HD but i think it doesn't matter, so:

Switch on the box and push button 2 on rc before displayed "boot", until you read: "multi" than push again 2 and wait!

Sorry my english, i write from hungary.

Pogifej.
 
Last edited:
B

Bro1

Registered
Messages
278
this was image i try

http://www.sat-universe.com/showthread.php?t=133188

Press number button which you want on RCU when start decoder.
Multiboot function supports as below style.
# 1 boot with CDKroot(NFS)
# 2 boot from USB memory stick, with internal HDD
# 3 original images as current flash memory
# 4 boot with NFS
# 5 boot from USB memory stick, but without internal HDD
# 6 boot from internal SATA HDD
# 7 boot from flash memory for another image

after flashing that i put e2 image into media folder,i then telnet to box
cd /media
tar xzf 9000_usb.tar.gz
sync
sync

afer that i reboot box and press 6......

it stays stuck on booting
 
B

Bro1

Registered
Messages
278
tryed the e2 on hardrive tutorial and this is putty log,,,box does not boot to e2


welcome to cuberevo
cuberevo login: root
Password:
Login incorrect
cuberevo login: root
Password:
System bootup in progress - please wait
[Disconnect bypassed -- root login allowed.]
CubeRevo 9000
Custom release - No Limits Board --> http://www.nlb.to

Release Edition - nlb11102
[NLB cuberevo /]$ cd /media
[NLB cuberevo media]$ tar xzf 9000_usb.tar.gz
[NLB cuberevo media]$ cd release
-sh: cd: release: No such file or directory
[NLB cuberevo media]$ mv * ../
mv: unable to open `../9000_usb.tar.gz': Read-only file system
mv: overwrite `../bin'? n
mv: overwrite `../boot'? n
mv: cannot remove `../dev': Read-only file system
mv: cannot create directory `../dev.static': Read-only file system
mv: overwrite `../etc'? n
mv: unable to open `../filelist.****': Read-only file system
mv: cannot create directory `../hdd': Read-only file system
mv: overwrite `../lib'? n
mv: cannot create directory `../lost+found': Read-only file system
mv: cannot remove `../media': Read-only file system
mv: cannot remove `../mnt': Read-only file system
mv: cannot create directory `../multi': Read-only file system
mv: unable to open `../myPanel.log': Read-only file system
mv: cannot remove `../proc': Read-only file system
mv: cannot create directory `../radio': Read-only file system
mv: cannot create directory `../ram': Read-only file system
mv: overwrite `../root'? n
mv: overwrite `../sbin'? n
mv: cannot remove `../sys': Read-only file system
mv: cannot remove `../tmp': Read-only file system
mv: unable to open `../tmp_SALENTO_CH-04012010-14_05_34_1681692777.ifo': Read-only file system
mv: cannot create directory `../tv': Read-only file system
mv: overwrite `../usr'? n
mv: cannot remove `../var': Read-only file system
mv: cannot create directory `../~tmp_SALENTO_CH-04012010-14_05_34_1681692777': Read-only file system
[NLB cuberevo media]$ n
-sh: n: command not found
[NLB cuberevo media]$ n
-sh: n: command not found
[NLB cuberevo media]$ n
-sh: n: command not found
[NLB cuberevo media]$ n
-sh: n: command not found
[NLB cuberevo media]$ n
-sh: n: command not found
[NLB cuberevo media]$ n
-sh: n: command not found
[NLB cuberevo media]$ n
-sh: n: command not found
[NLB cuberevo media]$ n
-sh: n: command not found
[NLB cuberevo media]$ sync
[NLB cuberevo media]$ sync
[NLB cuberevo media]$ fw_setenv menu_1 'setenv bootargs "console=ttyAS1,115200 panic=3 root=/dev/mtdblock3 bigphysarea=1500";setenv bootcmd "bootm a0060000";save;boot'
Unlocking flash...
Done
Erasing old environment...
Done
Writing environment to /dev/mtd1...
Done
Locking ...
Done
[NLB cuberevo media]$ fw_setenv menu_2 'setenv ipaddr 10.1.1.181;setenv gateway 10.1.200;setenv netmask 255.255.255.0;setenv bootide "run bootargside;ide reset;ext2load ide 0:2 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargside "setenv bootargs console=ttyAS1,115200 panic=3 root=/dev/sda2 rw rootfstype=ext2 init=/bin/devinit ip=$ipaddr::$gateway:$netmask mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000";setenv bootcmd "run bootide";save;boot'
Unlocking flash...
Done
Erasing old environment...
Done
Writing environment to /dev/mtd1...
Done
Locking ...
Done
[NLB cuberevo media]$


used latest nlb image and latest e2 usb image from here
 
J

jamie-warez

VIP
Messages
700
From thr above it looks like you have another version of e2 on your disk
with is the reason for the (Read-only file system)

I would Use
Installations Utility Enigma 1/2
from here http://www.sat-universe.com/showthread.php?t=144540
Its easy to use Here is a litttle guide

Step 1: Under the setup tab select the type of image you have on your box! then enter your boxes ip/password.
After that click connect!

Step 2: Cick the format tab! then select your disk from the device dropdown..Sda1 is normaly your harddisk and sdb1 is your usb device!
After selcecting your device click unmount!
then click format!
Now wait untill your hdd is formated it will give the message in the consol window!
After this click Mount...

step3 click open e2 and select your tar.gz image. now click copy... then click unpack..
it will now install e2 to your hard disk!
after its done! if you like you can install extra fixes and stuff from the addons button! the add mboot is needed to edit your boot commands in the multiboot tab!
This only works after you are in e2 so you have to install one of the other multoboots that are going around. some images allready have the multiboot installed!
Click to expand...

Hope this helps....
If you need anyhelp m8 let me know i can help you on msn if you like!
 
Last edited:
B

Bro1

Registered
Messages
278
cheers for that jamie ,i will have a try of that now mate,been banging my head against the wall with this,have no probs with doing it on usb stick lol :thum:
 
B

Bro1

Registered
Messages
278
one thing in my dropdown i have sda1 and sda2 i think it said but i dont have usb stick in os could this be the prob,tried above and still stuck on booting :mecry::D
 
J

jamie-warez

VIP
Messages
700
you need to fdisk to just one partition m8!

so you have just sda1 if you have both then the e2 wont boot!

you can use 2 partitions but you need to do all manualy and make sure sda1 is your main partition and not a swap!

The enigmaUI should sort your partitions out just click fdisk button before step 2 m8 and it should run all the commands needed to get just sda1 on your box! then run step 2 and 3 again and all should be ok
 
Last edited:
B

Bro1

Registered
Messages
278
k mate cheers will do,,,just got to nip out for an hour then will have another bash,may reinstall nlb image then format hardrive first :D
 
D

dirtydogs

Registered
Messages
14
jamie-wareez said:
you need to fdisk to just one partition m8!

so you have just sda1 if you have both then the e2 wont boot!

you can use 2 partitions but you need to do all manualy and make sure sda1 is your main partition and not a swap!

The enigmaUI should sort your partitions out just click fdisk button before step 2 m8 and it should run all the commands needed to get just sda1 on your box! then run step 2 and 3 again and all should be ok
Click to expand...

Thanks for the advise Jamie. Been stuck for a while with this problem.

dickie
 
B

Bro1

Registered
Messages
278
been on msn with jamie and still no luck,for some reason it dont boot for me

thanks jamie for the help by the way:thum:
 
B

Bro1

Registered
Messages
278
jamie-wareez said:
you need to fdisk to just one partition m8!

so you have just sda1 if you have both then the e2 wont boot!

you can use 2 partitions but you need to do all manualy and make sure sda1 is your main partition and not a swap!

The enigmaUI should sort your partitions out just click fdisk button before step 2 m8 and it should run all the commands needed to get just sda1 on your box! then run step 2 and 3 again and all should be ok
Click to expand...

followed this to the letter,put that 9000 file on earlier you gave me and still stuck on booting,only bit i didnt do was this .......mboot is needed to edit your boot commands in the multiboot tab!
 
You must log in or register to reply here.
Top