Decoder As a Modem

[[email protected]]

Please could I be advised how i could use my Strong 4669x decoder as internet modem or for offline browsing. I have searched round without success but I have a hint that it is possible. Mikkyray asked this question 12-10-2009 without any reply.

 

[sanobi1]

get a cable modem

 

[[email protected]]

@sanobi1
Thanks for your response. Please could you explain what you mean by cable modem or perhaps explain all the requirements and the procedure to me at a go.
I have a USB DVB-S Box, I also have routers and the USB to Serial cable to connect my decoder to my laptop or desktop.

I will be looking forward to your response.

 

[asjad]

if your decoder is dvb card then you can enjoy grabbing which is actually offline browsing

 

[[email protected]]

@asjad
Thanks.
Please how do I go about the grabbing either with my Strong SRT4669x which is a DVR (MPEG4) or the USB DVB-S box.

 

[balolconi]

decoder modem

You need a splitter and a cable modem and a serial to ethernet converter board.

 

[Drdanskills]

U need to have d following items: decoder & card with valid subscription, cable modem, splitter, RJ-45 cable, coaxial cable.
Connect the Coaxial Cable from the Coaxial
Port at the back of the Decoder to the Splitter.
2. Connect another Coaxial Cable from the
other side of the splitter to the Coaxial Port at
the back of Cable Modem.
3. Connect one end of the Rj-45 Cable to the
jack of the Cable Modem and the other end of
the cable to the Ethernet port of your Laptop
or your Desktop PC.
4. Turn on your Decoder and also turn on the
Cable Modem.
Thats All, Is that not very Simple? I know you
Understand every bit of it, Now lets Proceed
to the Browser Configuration Stage.
CONFIGURE YOUR BROWSER TO WORK WITH
THE DECORDER
Now we are 95% done, Just Configure your
Browser with the Below IP and Port and you
can Start Surfing the Internet at an
Unimaginable Speed of 8mbps all for Free,
Now Open your Mozilla or any other Browser
and configure with this:
HTTP proxy or IP: 127.0.0.1
PORT: 8080
or select Auto Detect Proxy and you are
Ready to Browse.

 

[[email protected]]

@Drdanskills

Thank you very much. I will work on it in the next few weeks when I must have subscribed.

Regards.

 

[Maraonline]

U need to have d following items: decoder & card with valid subscription, cable modem, splitter, RJ-45 cable, coaxial cable.
Connect the Coaxial Cable from the Coaxial
Port at the back of the Decoder to the Splitter.
2. Connect another Coaxial Cable from the
other side of the splitter to the Coaxial Port at
the back of Cable Modem.
3. Connect one end of the Rj-45 Cable to the
jack of the Cable Modem and the other end of
the cable to the Ethernet port of your Laptop
or your Desktop PC.
4. Turn on your Decoder and also turn on the
Cable Modem.
Thats All, Is that not very Simple? I know you
Understand every bit of it, Now lets Proceed
to the Browser Configuration Stage.
CONFIGURE YOUR BROWSER TO WORK WITH
THE DECORDER
Now we are 95% done, Just Configure your
Browser with the Below IP and Port and you
can Start Surfing the Internet at an
Unimaginable Speed of 8mbps all for Free,
Now Open your Mozilla or any other Browser
and configure with this:
HTTP proxy or IP: 127.0.0.1
PORT: 8080
or select Auto Detect Proxy and you are
Ready to Browse.

Hi! Very good idea but how that can be possible without RF unit? Lnb can be RX and which one will be used as TX? Please explain!

 

[biss1]

Hi! Very good idea but how that can be possible without RF unit? Lnb can be RX and which one will be used as TX? Please explain!

The cable modem can sort both RX and TX from signal coming through the LNB since it carries both data and video.

 

[OLALEKANSHODIYA]

I have SRT 4661x I want anybody to help me out on software to view free scramble station

 

[clemegas]

Thanks for this post. I will give it a trial and get back. You guys are gr8

 

[jollymich]

Please I want to know if I must use valid subscription before I can connect the internet using Toshiba pcx2600 cable modem and strong 4669z please reply.

 

[Mylife4real86]

U need to have d following items: decoder & card with valid subscription, cable modem, splitter, RJ-45 cable, coaxial cable.
Connect the Coaxial Cable from the Coaxial
Port at the back of the Decoder to the Splitter.
2. Connect another Coaxial Cable from the
other side of the splitter to the Coaxial Port at
the back of Cable Modem.
3. Connect one end of the Rj-45 Cable to the
jack of the Cable Modem and the other end of
the cable to the Ethernet port of your Laptop
or your Desktop PC.
4. Turn on your Decoder and also turn on the
Cable Modem.
Thats All, Is that not very Simple? I know you
Understand every bit of it, Now lets Proceed
to the Browser Configuration Stage.
CONFIGURE YOUR BROWSER TO WORK WITH
THE DECORDER
Now we are 95% done, Just Configure your
Browser with the Below IP and Port and you
can Start Surfing the Internet at an
Unimaginable Speed of 8mbps all for Free,
Now Open your Mozilla or any other Browser
and configure with this:
HTTP proxy or IP: 127.0.0.1
PORT: 8080
or select Auto Detect Proxy and you are
Ready to Browse.

WHAT ABOUT SRT4930 WITH LAN PORT

 

[Olayinka07]

where can i get cable moderm and it cost like how much ?

 

[Olayinka07]

pls help on how to connect my strong 4930l decoder to browse in my pc thanks

 

[elkirf]

my decoder does not have a lan port, how do i go about it?