c-line
- Thread starter hambone
- Start date
jamie-warez
VIP
- Messages
- 700
There is no cccam for sh4 ipbox/cuberevo
Its Fake and just a renamed edited mgmcamd. Oscam is the most stable cccam cliant for your box...
Here is a post for some info on how to add your cline to oscam...
http://www.sat-universe.com/showthread.php?t=173741
Its Fake and just a renamed edited mgmcamd. Oscam is the most stable cccam cliant for your box...
Here is a post for some info on how to add your cline to oscam...
http://www.sat-universe.com/showthread.php?t=173741
thanks for the reply jamie.
i have tried editing the oscam.server oscam.conf and oscam.user files but i am still getting blank screens.
i replaced the server info and username and pass in oscam.server with the details of the payserver. i then copied oscam.user and oscam.conf as contained in the reply
http://www.sat-universe.com/showthread.php?t=173741
i can see the ecm info on screen with server details etc but still no picture
but i think what i need is an expert to tell me exactly what i need to replace in the oscam files?
the oscam client downloaded and installed from online 2 is oscam.stapi.
i also tried running cccam 2.1.4
thanks
ham
i have tried editing the oscam.server oscam.conf and oscam.user files but i am still getting blank screens.
i replaced the server info and username and pass in oscam.server with the details of the payserver. i then copied oscam.user and oscam.conf as contained in the reply
http://www.sat-universe.com/showthread.php?t=173741
i can see the ecm info on screen with server details etc but still no picture
but i think what i need is an expert to tell me exactly what i need to replace in the oscam files?
the oscam client downloaded and installed from online 2 is oscam.stapi.
i also tried running cccam 2.1.4
thanks
ham
thanks zippy
i tried the converter but it just brings up an dialog box saying there was an error converting cccam.cfg.
it displays the 3 c lines but obviously it isnt converting the file.
maybe the cccam.cfg file would be easier applied if i was running an e2 image?
thanks
ham
i tried the converter but it just brings up an dialog box saying there was an error converting cccam.cfg.
it displays the 3 c lines but obviously it isnt converting the file.
maybe the cccam.cfg file would be easier applied if i was running an e2 image?
thanks
ham
I have oscam 1.10rc by JARO build 5741 and my line converts to
[reader]
label=server1
enable=1
protocol=cccam
device=something.someting.something,port
user=user
password=password
cccwantemu=0
cccversion=2.2.1
group=1
inactivitytimeout=1
reconnecttimeout=30
lb_weight=100
cccversion=2.2.1
cccmaxhops=3
cccwantemu=1
ccckeepalive=1
You need to change acordingly:
label=
device=
user=
password=
cccversion=
[reader]
label=server1
enable=1
protocol=cccam
device=something.someting.something,port
user=user
password=password
cccwantemu=0
cccversion=2.2.1
group=1
inactivitytimeout=1
reconnecttimeout=30
lb_weight=100
cccversion=2.2.1
cccmaxhops=3
cccwantemu=1
ccckeepalive=1
You need to change acordingly:
label=
device=
user=
password=
cccversion=
many thanks for the replies guys but i am still unable to get it to work.
i have tried inserting the ip and port contained in the clines in oscam.server and the same with the user and pass word provided but still no picture.
i have decided to start from scratch.
here is my current unmodified oscam.server file and below is the cccam.cfg file there is also a cccam.prio file and i dont know where this needs to go
maybe there is something i am doing which isnt quite right?
this is oscam.stapi
[reader]
enable = 1
Label = reader
Protocol = internal
Device = /dev/sci0
#boxid = 11111111
Group = 1
Caid = 0919
#Ident = 0919:000000
Detect = CD
#deprecated = 1
#mhz = 600
#cardmhz = 600
#CustomSpeed = 0
[reader]
enable = 1
Label = pcsc0
Protocol = pcsc
Device = 0
Group = 1
lb_weight = 1
cardmhz = 368
emmcache = 1,1,2
tiger_rsakey = A92DA72FEEACF2947B003ED652153B189E4043B0138C368BDF6B9ED77DDAD6C0761A2198AEB3FC97A19C9D01CA769B3FFFE4F6E70FA4E0696A8980E18D8C58E11D817121346E3E66457FDD84CFA72589B25B538EFC304361B54845F39E9EFA52D805E5FD86B595B366C35716ABC91FA3DC159C9F4D8164B5
blockemm-u = 0
blockemm-s = 0
blockemm-g = 0
blockemm-unknown = 1
[reader]
enable = 0
Label = pcsc1
Protocol = pcsc
Device = 1
Group = 1
lb_weight = 1
[reader]
enable = 0
Label = pcsc2
Protocol = pcsc
Device = 2
Group = 1
lb_weight = 1
[reader]
#cccdisableautoblock = 1
enable = 0
label = cccamreader
protocol = cccam
device = 192.168.1.12,12000
account = dummy,dummy
group = 1
#disableserverfilter = 1
#caid = 0919
#Ident = 0919:000000
cccversion = 2.1.1
cccbuild = 2971
[reader]
enable = 0
Label = SMARGO_mouse
Protocol = mouse
Device = /dev/ttyUSB0
Group = 1
--------------------------------------------------------------
ip port user pass
C: (xxxx.xxxx.com) (xxxxx) (xxxx) (xxxx)
C: (xxxx.xxxx.com) (xxxxx) (xxxx) (xxxx)
C: (xxxx.xxxx.com) (xxxxx) (xxxx) (xxxx)
SERVER LISTEN PORT : xxxxx
ALLOW TELNETINFO: yes
ALLOW WEBINFO: yes
WEBINFO USERNAME :
WEBINFO PASSWORD :
TELNETINFO USERNAME :
TELNETINFO PASSWORD :
TELNETINFO LISTEN PORT : 16000
WEBINFO LISTEN PORT : 15001
ZAP OSD TIME :0
OSD USERNAME :
OSD PORT :80
# SERIAL READER :
# SMARTCARD WRITE DELAY :
# SMARTCARD CLOCK FREQUENCY
#SMARTCARD CLOCK FREQUENCY: /dev/sci0 6300000 #lower
#SMARTCARD CLOCK FREQUENCY: /dev/sci1 6300000 #upper
B: /dev/sci0 07
#B: /dev/sci1 07
# EMM Blocker
SHOW TIMING : no
DEBUG : no
NEWCAMD CONF :no
DISABLE EMM : yes
EXTRA EMM LEVEL : no
MINI OSD : no
#CAM KEY
#CAMDATA
#BOX KEY
#BEEF ID :
#PIN :
#SOFTKEY FILE : /var/keys/SoftCam.Key
#AUTOROLL FILE : /var/keys/AutoRoll.Key
#STATIC CW FILE : /var/keys/constant.cw
CAID PRIO FILE : /var/etc/CCcam.prio
PROVIDERINFO FILE : /var/etc/CCcam.providers
CHANNELINFO FILE : /var/etc/CCcam.channelinfo
i have tried inserting the ip and port contained in the clines in oscam.server and the same with the user and pass word provided but still no picture.
i have decided to start from scratch.
here is my current unmodified oscam.server file and below is the cccam.cfg file there is also a cccam.prio file and i dont know where this needs to go
maybe there is something i am doing which isnt quite right?
this is oscam.stapi
[reader]
enable = 1
Label = reader
Protocol = internal
Device = /dev/sci0
#boxid = 11111111
Group = 1
Caid = 0919
#Ident = 0919:000000
Detect = CD
#deprecated = 1
#mhz = 600
#cardmhz = 600
#CustomSpeed = 0
[reader]
enable = 1
Label = pcsc0
Protocol = pcsc
Device = 0
Group = 1
lb_weight = 1
cardmhz = 368
emmcache = 1,1,2
tiger_rsakey = A92DA72FEEACF2947B003ED652153B189E4043B0138C368BDF6B9ED77DDAD6C0761A2198AEB3FC97A19C9D01CA769B3FFFE4F6E70FA4E0696A8980E18D8C58E11D817121346E3E66457FDD84CFA72589B25B538EFC304361B54845F39E9EFA52D805E5FD86B595B366C35716ABC91FA3DC159C9F4D8164B5
blockemm-u = 0
blockemm-s = 0
blockemm-g = 0
blockemm-unknown = 1
[reader]
enable = 0
Label = pcsc1
Protocol = pcsc
Device = 1
Group = 1
lb_weight = 1
[reader]
enable = 0
Label = pcsc2
Protocol = pcsc
Device = 2
Group = 1
lb_weight = 1
[reader]
#cccdisableautoblock = 1
enable = 0
label = cccamreader
protocol = cccam
device = 192.168.1.12,12000
account = dummy,dummy
group = 1
#disableserverfilter = 1
#caid = 0919
#Ident = 0919:000000
cccversion = 2.1.1
cccbuild = 2971
[reader]
enable = 0
Label = SMARGO_mouse
Protocol = mouse
Device = /dev/ttyUSB0
Group = 1
--------------------------------------------------------------
ip port user pass
C: (xxxx.xxxx.com) (xxxxx) (xxxx) (xxxx)
C: (xxxx.xxxx.com) (xxxxx) (xxxx) (xxxx)
C: (xxxx.xxxx.com) (xxxxx) (xxxx) (xxxx)
SERVER LISTEN PORT : xxxxx
ALLOW TELNETINFO: yes
ALLOW WEBINFO: yes
WEBINFO USERNAME :
WEBINFO PASSWORD :
TELNETINFO USERNAME :
TELNETINFO PASSWORD :
TELNETINFO LISTEN PORT : 16000
WEBINFO LISTEN PORT : 15001
ZAP OSD TIME :0
OSD USERNAME :
OSD PORT :80
# SERIAL READER :
# SMARTCARD WRITE DELAY :
# SMARTCARD CLOCK FREQUENCY
#SMARTCARD CLOCK FREQUENCY: /dev/sci0 6300000 #lower
#SMARTCARD CLOCK FREQUENCY: /dev/sci1 6300000 #upper
B: /dev/sci0 07
#B: /dev/sci1 07
# EMM Blocker
SHOW TIMING : no
DEBUG : no
NEWCAMD CONF :no
DISABLE EMM : yes
EXTRA EMM LEVEL : no
MINI OSD : no
#CAM KEY
#CAMDATA
#BOX KEY
#BEEF ID :
#PIN :
#SOFTKEY FILE : /var/keys/SoftCam.Key
#AUTOROLL FILE : /var/keys/AutoRoll.Key
#STATIC CW FILE : /var/keys/constant.cw
CAID PRIO FILE : /var/etc/CCcam.prio
PROVIDERINFO FILE : /var/etc/CCcam.providers
CHANNELINFO FILE : /var/etc/CCcam.channelinfo
Last edited:
Are you sure that you have oscam emu installed properly. I use BMT Kraken which by default has all configuration files and scripts to stop/start/restart cam but the cam is not there by default.
I downloaded the oscam-1.10rc-by_jaro5741-sh4-linux-stapi.tar.gz then extracted the file "oscam" and copied it with ftp to var/bin, changed permissions to 755 and finally restarted the box.
The config should be adjusted to a version of oscam. In this version there is not parameter "account" and you must you use parameters "user" and "password".
I downloaded the oscam-1.10rc-by_jaro5741-sh4-linux-stapi.tar.gz then extracted the file "oscam" and copied it with ftp to var/bin, changed permissions to 755 and finally restarted the box.
The config should be adjusted to a version of oscam. In this version there is not parameter "account" and you must you use parameters "user" and "password".
thanks to all those who have helped me.
i have still had no luck in getting oscam configured and a family matter has came up which means i dont really have the time to solve my problem.(unless it was a case of ftp'ing the config file into the correct var/ folder relevant to the image and cam being used).
i will return to the box fresh from a different angle with possibly a different server provider and maybe different images hopefully within the next couple of weeks.
i will post on here when i get success
thanks again
ham
i have still had no luck in getting oscam configured and a family matter has came up which means i dont really have the time to solve my problem.(unless it was a case of ftp'ing the config file into the correct var/ folder relevant to the image and cam being used).
i will return to the box fresh from a different angle with possibly a different server provider and maybe different images hopefully within the next couple of weeks.
i will post on here when i get success
thanks again
ham
jamie-warez
VIP
- Messages
- 700
what provider are you using?
satactive
update.
still blank screens
i have re-installed SifTeam-0.7.0-r13791 for Ipbox 900/910 HD
installed oscam-stapi from online panel.
i have tried a different provider who have givem me a cccam.cfg file with 4 c-lines.
i have used oscam to cccam converter and got the following oscam.server file which i have placed in var/etc/oscam.
[reader]
label=************
enable=1
protocol=cccam
device=************
user=************
password=************
cccwantemu=1
cccversion=2.1.2
group=1
inactivitytimeout=1
reconnecttimeout=30
lb_weight=100
cccversion=2.1.2
cccmaxhops=10
ccckeepalive=1
[reader]
label=************
enable=1
protocol=cccam
device=************
user=************
password=************
cccwantemu=1
cccversion=2.1.2
group=1
inactivitytimeout=1
reconnecttimeout=30
lb_weight=100
cccversion=2.1.2
cccmaxhops=10
ccckeepalive=1
[reader]
label=************
enable=1
protocol=cccam
device=************
user=************
password=************
cccwantemu=1
cccversion=2.1.2
group=1
inactivitytimeout=1
reconnecttimeout=30
lb_weight=100
cccversion=2.1.2
cccmaxhops=10
ccckeepalive=1
[reader]
label=************
enable=1
protocol=cccam
device=************
user=************
password=************
cccwantemu=1
cccversion=2.1.2
group=1
inactivitytimeout=1
reconnecttimeout=30
lb_weight=100
cccversion=2.1.2
cccmaxhops=10
ccckeepalive=1
stil blank screens.
i am ready to give up on this box but maybe someone can see something simple that needs changed?
thanks in advance
still blank screens
i have re-installed SifTeam-0.7.0-r13791 for Ipbox 900/910 HD
installed oscam-stapi from online panel.
i have tried a different provider who have givem me a cccam.cfg file with 4 c-lines.
i have used oscam to cccam converter and got the following oscam.server file which i have placed in var/etc/oscam.
[reader]
label=************
enable=1
protocol=cccam
device=************
user=************
password=************
cccwantemu=1
cccversion=2.1.2
group=1
inactivitytimeout=1
reconnecttimeout=30
lb_weight=100
cccversion=2.1.2
cccmaxhops=10
ccckeepalive=1
[reader]
label=************
enable=1
protocol=cccam
device=************
user=************
password=************
cccwantemu=1
cccversion=2.1.2
group=1
inactivitytimeout=1
reconnecttimeout=30
lb_weight=100
cccversion=2.1.2
cccmaxhops=10
ccckeepalive=1
[reader]
label=************
enable=1
protocol=cccam
device=************
user=************
password=************
cccwantemu=1
cccversion=2.1.2
group=1
inactivitytimeout=1
reconnecttimeout=30
lb_weight=100
cccversion=2.1.2
cccmaxhops=10
ccckeepalive=1
[reader]
label=************
enable=1
protocol=cccam
device=************
user=************
password=************
cccwantemu=1
cccversion=2.1.2
group=1
inactivitytimeout=1
reconnecttimeout=30
lb_weight=100
cccversion=2.1.2
cccmaxhops=10
ccckeepalive=1
stil blank screens.
i am ready to give up on this box but maybe someone can see something simple that needs changed?
thanks in advance
i am trying to use a cccam premium server.
i have been sent a cccam.cfg file which contains the address port username and password for login etc.
i have tried this file using cccam 2.1.4 emu on sifteam r13971 but nothing will clear.
i have tried using oscam-stapi and inserted the relevant details from the provider in oscam.server but still nothing.
i have tried 2 different providers so the problem must be in the emu config.
if i select cccam emu and place the file in var/keys i get ecm info and server details on screen by pressing green then no 3 this displays server signature and response time of milliseconds but nothing clears.
if only i could enter my providers details in one of the emu available from online2 to get box to connect tomy cccam server.
In /var/keys whe must have these settings :
[global]
nice=-10
pidfile=/tmp/oscam.pid
#logfile=/tmp/oscam.log
#logfile=/dev/null
disablelog=1
disableuserfile=1
maxlogsize=32
waitforcards=0
#waitforcards=1
preferlocalcards=0
#preferlocalcards=1
cachedelay=0
# WEBIF ----------------------------------------------------
[webif]
httpport=668
httpallowed=127.0.0.1,192.168.1.1-192.168.1.255
[cccam]
port = 13000
version = 2.1.4
build = 3598
reshare = 2
[dvbapi]
enabled=1
# boxtype: dbox2|dreambox|ufs910|ipbox
boxtype=ufs910
user=local
au=1
-Then whe go in oscam.user and create a account for the peer, example :
[account]
user=demo
pwd=500
group=1,2,3,4
uniq=0
-The C-line that whe make for the peer is like this :C: ip_adress 13000 demo 500
[global]
nice=-10
pidfile=/tmp/oscam.pid
#logfile=/tmp/oscam.log
#logfile=/dev/null
disablelog=1
disableuserfile=1
maxlogsize=32
waitforcards=0
#waitforcards=1
preferlocalcards=0
#preferlocalcards=1
cachedelay=0
# WEBIF ----------------------------------------------------
[webif]
httpport=668
httpallowed=127.0.0.1,192.168.1.1-192.168.1.255
[cccam]
port = 13000
version = 2.1.4
build = 3598
reshare = 2
[dvbapi]
enabled=1
# boxtype: dbox2|dreambox|ufs910|ipbox
boxtype=ufs910
user=local
au=1
-Then whe go in oscam.user and create a account for the peer, example :
[account]
user=demo
pwd=500
group=1,2,3,4
uniq=0
-The C-line that whe make for the peer is like this :C: ip_adress 13000 demo 500