ASH on display using usb adapter

[duckkayak]

I have a problem which isn't being replied to in the correct section. I have bought several boxes, EL 3020 ir plus but some people have new laptops which don't have the rs232 cable so I am trying to use a USB to rs232 adaptor and am now getting a target connect error with ASH shown on the display.

I can use my older laptop with the rs232 cable and it works fine and the message disappears. I've downloaded the patch for the ON/ASH problem but it still does the same.

Port settings, baud rate etc etc are correct and match the alimupg55 program settings. I'm hoping this is a more common problem with these USB adaptors and not specific to these boxes which is why I'm asking here as it might affect other boxes too.

Can anyone help.

TIA

 

[bakenah]

hello my friend...........

that is a hardware problem, friend of my had thesame but not working..........................

 

[bakenah]

pls what about orbit ?

 

[VFL]

for me too some use usb adapte not work

 

[duckkayak]

that is a hardware problem, friend of my had thesame but not working..........................

I can't believe it is a hardware problem when it works fine with the normal cable and the USB adaptor shouldn't change anything but something is making the display show the ASH message.

Help!

 

[zamrossa]

iv read somewhere that wat u need is converter (which come with cd for driver) not adapter
then u need to go to device manager chose ports then chose ur converter go to properties then change the bit to 128000
data bit 7
parity none
stop bits 1
flow control none
try this it may
by the way i tried it and it didnt work for me it may work for u please let me know if it did

 

[duckkayak]

iv read somewhere that wat u need is converter (which come with cd for driver) not adapter
then u need to go to device manager chose ports then chose ur converter go to properties then change the bit to 128000
data bit 7
parity none
stop bits 1
flow control none
try this it may
by the way i tried it and it didnt work for me it may work for u please let me know if it did

Thanks I'll try that but I'm sure I've tried every setting there is, I'll let you know.

 

[kure-ka]

Thanks I'll try that but I'm sure I've tried every setting there is, I'll let you know.

I have the same ASH problem on my laptop with VISTA. Supprisingly, I have been using this same laptop and USB to Serial converter for the past 8months or so. I read in one of the forums that it might be a windows problem. Can somebody PLEASE help

 

[Girinum]

try to use short rs232 cable the converter already with long cable ( the only stb can work with a long cable 6300 cause it had a power rs232 inside )
2- in device manager see wich port you use when you put the converter

 

[kure-ka]

try to use short rs232 cable the converter already with long cable ( the only stb can work with a long cable 6300 cause it had a power rs232 inside )
2- in device manager see wich port you use when you put the converter

I have try using a shorter cable, but the ASH is still there. Is there nobody in the UNIVERSE that can find a solution to this problem?

 

[Girinum]

I have try using a shorter cable, but the ASH is still there. Is there nobody in the UNIVERSE that can find a solution to this problem?

Hi
little bug may inform Pc on work
be sure your Pc don't have any Virus inside Scan your Pc
defg your hard disk when you do update to Stb
be sure your Pc not busy in anything else don't open any Expl. or any other program
Everytime you wanna start an update do restart your Pc
if ASH apear turn off Stb unplug the converter and restart the Pc than plug the converter and start again it work for me

PS: if you don't wanna waste your time Keep your Stb on whatever software you have and just upgrade the Card
by insert in any receiver with latest software ( to any friend have receiver with Abra too )it will do Kv /Sv update than put in your Stb it will work

 

[jamildawaki]

I have the same problem with my laptop. I've tried all the suggested solutions but keeping getting the same ASH/RSH and/or Target errors when I use the USB to R232 converter.

Any other suggestions?

 

[kb5]

I have the same problem with my laptop. I've tried all the suggested solutions but keeping getting the same ASH/RSH and/or Target errors when I use the USB to R232 converter.

Any other suggestions?

is it on comm port 1.. I had this issue and in the end bought a new usb to R232 adaptor that worked ? good luck