Spanish Abertis DTT Sat @ Hispasat 30W - Chat & How to guides

Stevenvc19

Donating Member
Messages
47
Just installed my new SF8008 box and nearly everything is working fine, even the new TVE UHD, but I have issues with channels on 8001, 8002 and 8003 (12631V 30000 3/4). Anyone with the same issue or an idea what could be wrong?

Edited: Seems just to be a weak signal from the transponder :-(
Check your LNB for correct polarisation
 

roisiano

Registered
Messages
17
Hello:
Is there any easy option (script or similar) for Abertis (30.0W) channels using TvHeadend addon with CoreELEC (TV-Box, S905X3) ?

Thanks in advance and kind regards
 

Maxx@

Registered
Messages
88
11222 V , 11422 H
But it's not available on standard hardware. I have a signal on TBS 5925 but the picture stutters terribly.
 

pipino

Registered
Messages
197
Its clear that this transmission is temporary for Terrestrial Transmiters only , no way Televes ZAS box could manage this
It was clear that will happen .. this TP was not even in Abertis(Cellnex) NIT Table thru Hispasat , anyway the situation with DVB-T in Spain is Frozen until 2024 or maybe even more, (thanks to TELEVES and some other lobbies :( ...
 

Ramboide

Registered
Messages
202
I just realized that TVE UHD and UHD-2 have stopped broadcasting on Hispasat, I also saw that there is no signal on this transponder. It was good while it lasted. I could not receive these channels on DTT. Goodbye TVE UHD TV.
 

Stevenvc19

Donating Member
Messages
47
It was clear that will happen .. this TP was not even in Abertis(Cellnex) NIT Table thru Hispasat , anyway the situation with DVB-T in Spain is Frozen until 2024 or maybe even more, (thanks to TELEVES and some other lobbies :( ...
It surprises me because I found a newsarticle that said the UHD mux was about to roll out on a national scale. So when they want to broadcast from the sat fed relay transmitters, they have no other choise than to use a sat feed...
 

Ramboide

Registered
Messages
202
Running a blind scan on Hispasat, many MIS transponders on 11222 V - SR: 3000 / FEC; 2/3, but no channel is found when scanning these transponders.
 

Galway

Registered
Messages
9
Instructions for receiving the new Abertis Asturias Mux on 11502V with ApeBox 2C 4K UHD:

It is important to mention that the multistream search in System/More Settings is set to OFF!

To add the new stream, create a new line in the Keys menu.
Thereby enters the following
at SID 321 (this is the streamnr 801 in Hex)
at frequency 11502
at Keys the ones already found here.
Save and manual search
The four Px are loaded and can be seen.
Don't forget to activate the multistream setting again, otherwise the box won't find MIS packets anymore. ;)

Translated with www.DeepL.com/Translator (free version)
Hi I am looking for the Service ID for this new Mux as I am using an Edision Primo IP S2 receiver. Does anyone know what this is? many thanks in advance
 

Galway

Registered
Messages
9
30W-11502.12 V
DVB-S2/8PSK
SR-10200
FEC-3/4
Code:
0709:0ce4acee:ea7c:0000:1:0:0
Abertis PID 801 11502V SID 0x709
p:ABERTIS,c:031fff,c:150321,C:2600,f:5
Code:
make_channel({
  name = "Abertis PID 801",
  input = {
    "http://localhost:8001/1:0:1:709:EA7C:0:CE4ACEE:0:0:0:",
  },
  transform = {{
    format = "pipe",
      command = "/etc/astra/scripts/abertis 801",
  }},
  output = {
    "http://0.0.0.0:9999/abertis/pid801",
  },
})


it might have been nicer and easier to actually tell me that. In any case that cannot be the correct Service ID for the Edision Primo Receiver as it does not load that MUX and yes I have the correct keys. So there must be SID that works with these receivers - I receive ALL of the other TDT muxes.
 

EnoSat

Senior Member
Messages
1,952
then you have to experiment, because you can see the SID in the picture, which is directly from the TS source (or the algorithm for processing 11502V is not included in your FW - since it is new)
what ID value did you enter for the key?
 
Last edited:

Galway

Registered
Messages
9
then you have to experiment, because you can see the SID in the picture, which is directly from the TS source (or the algorithm for processing 11502V is not included in your FW - since it is new)
maybe someone else who is receiving this MUX using an Edision Primo or an Octagon SX88 can give me an answer I can understand
 
Last edited:
Top