Opticum X402p X403p CHAT

satamuse

Registered
Messages
322
1.5.37

Hi i confirm i've the same problem with this firmware then i flashed with an older
hi all
please note that the newest flash/firmware is the :
mine is a clone of yours....x4-x7......

yumatu_big_black synaps_galaxy_1.5.37_gi.tv
this last soft enable french tntsat to work again
enjoy
 

panopti

Registered
Messages
2
0000 followed by bootloop

hi sandhead
you have a problem in your power supply
some condensators are bad bulging - inflated bombé - gonflé )
replace
the green platics are all very bad quality !
regards

Hi,

I have a problem with my Opticum X402p perhaps similar to that of sandhead:
after flashing the STB via USB with software globo_x4_amstar_sab_1.5.38_gisclub.tv.abs (unfortunately without updating bootloader-ver.1.1.6 - stupid fault of mine!) I got a success-message, but since automatical reboot the box hangs in an endlessly bootloop.

By plugging off and on, display first shows "0000" for about 1 sec., afterwards looping between "ON" and "boot" infinitely. This problem seems to be due to corrupted bootdata rather then to damaged powersupply, since I can't detect any bulbing elkos in my box and measuring the voltage applied to motherboard shows correct values (with one exception: 22V-pin measures 25V instead).

Trying Software Upgrade via RS-232 by running EromUpgrade.exe (STB EROM Ugrade 2.0.0c, found in this forum) always gets "Please reset target!"-message; plugging STB off and on to electrical current even repeatedly does'nt change anything. Thus box seems to refuse any RS-232-communication, or can it be forced more powerful by direct-cloning a working X402p-box?

If not so, is there available a jtag-instruction suitable to Opticum X402p and its clones, or knows anyone another possibility of how to reanimate my STB? I would be very grateful for every working hint.

Thanks and happy new year!
 

babuvip

Registered
Messages
2
Hi Sat Universe Soon I will get Orton X403p from my Friend, So i hope here i will get some help to work that STB fine.
 

shoaib334

Registered
Messages
26
sir i want to enter 32 digit,
(Disney Channel Russia
CaID: 0x0602(Irdeto2)
SID:0x012F
CW: 586DCB6D3075BD2615B67BE0E854D148)
how to enter this key manually in my orton receiver,
and pls. give me the link of orton key editer too.
 

satamuse

Registered
Messages
322
sir i want to enter 32 digit,
(Disney Channel Russia
CaID: 0x0602(Irdeto2)
SID:0x012F
CW: 586DCB6D3075BD2615B67BE0E854D148)
how to enter this key manually in my orton receiver,
and pls. give me the link of orton key editer too.
hi
look here on this site for :
Orton Key Editor 1.4 28 october 2009
or
Orton Key Editor 1.8 02-april 2012
regards
they work for globo,OPTICUM HD X7, Golden Media Unibox etc....
regards
 

satamuse

Registered
Messages
322
Open this Mcaskey editor edit the keys in order and upload them later with USB Stick on your receiver.
The Keys are included in the upload are old.
Pick New!
http://www.megafileupload.com/en/file/574598/mcaskey-editor-rar.html
hi h1
i don't like the orton editor because it makes fakes keys that are
not unusable for my yumatu3602A.
i always use : key mcaskey editor (dreamer1983_27JAN2011).
shoaib334 should remenber that keys are NOT all !! the firmware
must be updated too....
i tried your link , but i was unable to download it .
...it was only to know the version of mcaskey editor : mine is
2.0.1.2
regards
 

weecooter

Registered
Messages
203
hi i have a orton x403p and its not switching on. on the front panal it says 0000 with the light on can some one help please thanks
 

satamuse

Registered
Messages
322
hi i have a orton x403p and its not switching on. on the front panal it says 0000 with the light on can some one help please thanks
hi weecooter
when the display shows 0000 it means that the power supply is ill
the power supply must be repared.green condensors are very bad quality : you will perhaps see that one or more condensor are
inflated, curved.
regards
 

sizan

Registered
Messages
10
@weecooter: change the 1000uF (25V i think)capacitor in the power unit inside the receiver. You will notice, the top is inflated a little bit.
 

michael602

Registered
Messages
1
X403p FTP firmware upgrade configuration problem

Hi All,

I have problem with X403p FTP server configuration for firmware update. I can't save my settings. Always after reboot STB I need to configure settings again, they still return defaults : ftp://192.168.3.12/pub and so one. Could someone tell me how to save my ftp server settings in STB? I tried in 5 diffrent version of firmware for this STB.
 

satamuse

Registered
Messages
322
power supply

@weecooter: change the 1000uF (25V i think)capacitor in the power unit inside the receiver. You will notice, the top is inflated a little bit.
hi
as i said................
but...
there is not only one peace 1000 , 330 eso......

please note that green capacitor=condensateur are always very bad quality and should be replace
regards
 
Top