Opticum HD x405p help!

startx

Registered
Messages
12
Hi gays I'm going yesterday to upgrade a software to x405p and in that moment is turning off the power, now my recirver it's bilking boot to front panel... I try to fix with rs232 but nothing happened! Can you Help me with some tools to restore my recirver to default function? Thx!


Sent from my iPhone using Tapatalk
 

startx

Registered
Messages
12
Thanks for your answer I have try that many times but nothing happened agen, it's look like my pc and receiver is not communicating like my receiver is dead! Does anyone know what's going on in that event?
 

satamuse

Registered
Messages
322
hi
please , first , control your power supply ( in the 405 box !!) very often it is due to bad condenseur-condensator !!!
if bumped ( edge not plane ) it is a bad condo
regards
else does your box have a usb port ?????
 

startx

Registered
Messages
12
hi

please , first , control your power supply ( in the 405 box !!) very often it is due to bad condenseur-condensator !!!

if bumped ( edge not plane ) it is a bad condo

regards

else does your box have a usb port ?????


Hi, yes i think the power supply it's look okay in the first seen, i dont know if inside have some problem!
my box have two usb.
29b5656a33b2b50988c21328fdd04338.jpg

ef02eae1fda60e8609661f5f2b42eb27.jpg


61e6961ebc1d3979f3d57f5ecb9b69db.jpg



Sent from my iPhone using Tapatalk
 

Andi12

Registered
Messages
190
Short Instructions:
1. Start Epromupgrade
2. Upgrade Mode Select
3. Select Origialsoft from the package
4. Incl. Choose Bootloader
5. Press Next
6. Opti. Shoot to the mains
7. Wait ...
8. Thereafter, the soft patch it

Shiko se mos te eshte koruptuar software mbase e ka prishur antivirusi,shkarkoje nje te ri dhe provoje perseri.


pac fat
 

satamuse

Registered
Messages
322
hi
good job for foto !
condensator (condo) looks like to be ok (plane and not bumped)
but.....the best think to do is to desold the capacity , if possible for you : control if court-circuit = shorted .
i see to something strange :
there are 4 diodes , the 4th in down position seemes to be " unpluged " = out of gate of the board ! see foto in next message !
diodes must measure in one way an infinity resitance and in the other way +/- 1 megohm !
you could compare the measure of the for diodes to see if one respond differently.
regards
 

satamuse

Registered
Messages
322
power supply x405

hi
good job for foto !
condensator (condo) looks like to be ok (plane and not bumped)
but.....the best think to do is to desold the capacity , if possible for you : control if court-circuit = shorted .
i see to something strange :
there are 4 diodes , the 4th in down position seemes to be " unpluged " = out of gate of the board ! see foto in next message !
diodes must measure in one way an infinity resitance and in the other way +/- 1 megohm !
you could compare the measure of the for diodes to see if one respond differently.
regards

http://i60.tinypic.com/2irohhv.jpg
 

startx

Registered
Messages
12
Short Instructions:

1. Start Epromupgrade

2. Upgrade Mode Select

3. Select Origialsoft from the package

4. Incl. Choose Bootloader

5. Press Next

6. Opti. Shoot to the mains

7. Wait ...

8. Thereafter, the soft patch it



Shiko se mos te eshte koruptuar software mbase e ka prishur antivirusi,shkarkoje nje te ri dhe provoje perseri.





pac fat


Flm per ket manual qe me dhe, do ta shikoj me vone se s'kam pas kohe kto dy ditet e fundit. Kurse sa per punen e andivirusit nuk mendoj te kem ndonje problem me sw se une nuk mbaj kurre nje te tille ne kompjuter keshtu qe mendoj se dicka tjeter duhet te kete resirveri, gjithsesi do ta shikoj dhe nje here se cfare mund te bej.

hi

good job for foto !

condensator (condo) looks like to be ok (plane and not bumped)

but.....the best think to do is to desold the capacity , if possible for you : control if court-circuit = shorted .

i see to something strange :

there are 4 diodes , the 4th in down position seemes to be " unpluged " = out of gate of the board ! see foto in next message !

diodes must measure in one way an infinity resitance and in the other way +/- 1 megohm !

you could compare the measure of the for diodes to see if one respond differently.

regards


Sorry for my answer because I was busy for two days! I can't change the things you told me because I have no parts. I'm looking for another power supply to change and to try again for flashing my box.


Sent from my iPhone using Tapatalk
 
Top