New RG v. 6.3 - v6.4 and now 6.5 by Maestro MAHDI!!!
HOW TO PROGRAMME YOUR SAMMY
Switch your Sammy off at the back BEFORE you program the EMU in!
After Sammy has cooled down a bit [say 2-3 minutes] switch it on at the back and keep it on Standby.
Now start the STUDIO 1.2 [or 1.3] by Maestro MAHDI and go to DSR FW Loader and Send FW, then choose the Emu [now 6.3] and Open -> to put the EMU in. Wait for the clock on Sammy display, do not rush!
HOW TO GET YOUR AU TO WORK
Using your remote, start your Sammy from Standby and do a RESET OF EMU by pressing 0 + Menu on your remote, quickly in succession! Then go down to RESET TO EMU DEFAULTS and press the OK button on your remote.
Sammy will switch itself off now. Use your remote to start it from Standby.
Go to the EMU MENU [by pressing 0 + Menu in quick succession] and you will see the following configuration:
EMU - ON
EMM - ON
CAID Mode - AUTO
Sharing Mode - HSIC - that's for Humax CS [change to the protocol you need, when using CS; SSSP DSR for GBox and DSR for Sammy original]
DCW Delay - experiment to see which setting here gets you a better result
RS232 Delay - as above, see which setting here gets you a better result
PREMIERE, TPS and SRG SWISS
Here I couldn't get the picture, that is to say the AU on Premiere to work for me, so I changed the channel and it still didn't work. So, I put the receiver to Standby via Remote [do not kill it at the back - no need for that any more!], then I switched it back on immediately - and the picture came very quickly!!! Maybe I just didn't wait for long enough? Anyway, the AU is working nicely!
After that go to TPS/Canal+ France [France 4, or any channel on that transponder] and leave it there - the AU was very fast!
Then, go to SRG Swiss and wait a bit for AU here. A minute or two...
NOW PUT THE RAM.bin IN
Now put your Sammy to Standby, and then put the RAM.bin file [with all the other keys] in [Oys or Cruiser], then start your Sammy via remote. All working fine, including DigiTV!
GREAT JOB, MAHDI!!!
HOW TO PROGRAMME YOUR SAMMY
Switch your Sammy off at the back BEFORE you program the EMU in!
After Sammy has cooled down a bit [say 2-3 minutes] switch it on at the back and keep it on Standby.
Now start the STUDIO 1.2 [or 1.3] by Maestro MAHDI and go to DSR FW Loader and Send FW, then choose the Emu [now 6.3] and Open -> to put the EMU in. Wait for the clock on Sammy display, do not rush!
HOW TO GET YOUR AU TO WORK
Using your remote, start your Sammy from Standby and do a RESET OF EMU by pressing 0 + Menu on your remote, quickly in succession! Then go down to RESET TO EMU DEFAULTS and press the OK button on your remote.
Sammy will switch itself off now. Use your remote to start it from Standby.
Go to the EMU MENU [by pressing 0 + Menu in quick succession] and you will see the following configuration:
EMU - ON
EMM - ON
CAID Mode - AUTO
Sharing Mode - HSIC - that's for Humax CS [change to the protocol you need, when using CS; SSSP DSR for GBox and DSR for Sammy original]
DCW Delay - experiment to see which setting here gets you a better result
RS232 Delay - as above, see which setting here gets you a better result
PREMIERE, TPS and SRG SWISS
Here I couldn't get the picture, that is to say the AU on Premiere to work for me, so I changed the channel and it still didn't work. So, I put the receiver to Standby via Remote [do not kill it at the back - no need for that any more!], then I switched it back on immediately - and the picture came very quickly!!! Maybe I just didn't wait for long enough? Anyway, the AU is working nicely!
After that go to TPS/Canal+ France [France 4, or any channel on that transponder] and leave it there - the AU was very fast!
Then, go to SRG Swiss and wait a bit for AU here. A minute or two...
NOW PUT THE RAM.bin IN
Now put your Sammy to Standby, and then put the RAM.bin file [with all the other keys] in [Oys or Cruiser], then start your Sammy via remote. All working fine, including DigiTV!
GREAT JOB, MAHDI!!!
Last edited:
