Manual for relive you Qbox
If you are half dead Q_Box
When the decoder does not respond to command, or the screen stays black, sometimes with a reset (in Qbox Updater tightened in Reboot) on or off and turning on the switch back, the problem is solved.
If you do not respond in any way, nor have communication, LAN. In this case we have the COM port, and is what we are going to use.
We connect the serial cable crossover (Null modem) andalusia deco, and the PC. Remember that others are not connected (or should) with the two devices off.
It differs from normal (pin to pin) and line 2 in which one side comes up on the other as 3. And in turn 3 and 2. In addition, female-female.
We started the Qbox Updater (in this case version 1.0.7) and the program window:
Select the COM port as appropriate.
Uncheck the box, use LAN.
By doing this, is noted as the poster and the same LAN IP IP become mate.
Squished in QBOX Update.
In the window that opens, we will have to indicate where the image, select it, and give Open.
If we try to load a backup (QBF) out a window like this:
You can only restore the backup LAN.
Select an image (QBU) and we will say that is a cartelito Curran, hopefully.
We hope, and a few seconds after leaving a window indicating that the image is ready, and asking if we raise.
If we say that.
We replied that we hope that connecting Status
A few seconds later, leaving a window at the rear of the receiver, and with a sign saying to turn off and turn on the switch back to the deco.
In Status, says the same thing.
Normally, if we are loading an image, without having previously blocked deco, and turns off lights automatically, the window disappearing.
Begins to load the image. We can continue to progress, either in part, such as Total, in the Status section, with two blue bars that go forward.
If you have curiosity, clicking on Show Console, we see that all parties are charging. Gives time to all the load is slow, about 40 minutes.
When finished, leaving a window ad, and asked to reboot (Reboot). Accepted.
At this point, according to the experiences of each, can sting in Reboot or shut down, and turn a few seconds later, with the switch back.
The latter method is recommended for him SifTeam images.
If we decide to do with the program will first this:
And then this:
Accepted and ready
gracias lemas
Translated from Spanish to English by google
If you are half dead Q_Box
When the decoder does not respond to command, or the screen stays black, sometimes with a reset (in Qbox Updater tightened in Reboot) on or off and turning on the switch back, the problem is solved.
If you do not respond in any way, nor have communication, LAN. In this case we have the COM port, and is what we are going to use.
We connect the serial cable crossover (Null modem) andalusia deco, and the PC. Remember that others are not connected (or should) with the two devices off.
It differs from normal (pin to pin) and line 2 in which one side comes up on the other as 3. And in turn 3 and 2. In addition, female-female.
We started the Qbox Updater (in this case version 1.0.7) and the program window:
Select the COM port as appropriate.
Uncheck the box, use LAN.
By doing this, is noted as the poster and the same LAN IP IP become mate.
Squished in QBOX Update.
In the window that opens, we will have to indicate where the image, select it, and give Open.
If we try to load a backup (QBF) out a window like this:
You can only restore the backup LAN.
Select an image (QBU) and we will say that is a cartelito Curran, hopefully.
We hope, and a few seconds after leaving a window indicating that the image is ready, and asking if we raise.
If we say that.
We replied that we hope that connecting Status
A few seconds later, leaving a window at the rear of the receiver, and with a sign saying to turn off and turn on the switch back to the deco.
In Status, says the same thing.
Normally, if we are loading an image, without having previously blocked deco, and turns off lights automatically, the window disappearing.
Begins to load the image. We can continue to progress, either in part, such as Total, in the Status section, with two blue bars that go forward.
If you have curiosity, clicking on Show Console, we see that all parties are charging. Gives time to all the load is slow, about 40 minutes.
When finished, leaving a window ad, and asked to reboot (Reboot). Accepted.
At this point, according to the experiences of each, can sting in Reboot or shut down, and turn a few seconds later, with the switch back.
The latter method is recommended for him SifTeam images.
If we decide to do with the program will first this:
And then this:
Accepted and ready
gracias lemas
Translated from Spanish to English by google