How to save yer fooked AZbox HD...

candyman2

Donating Member
Messages
71
It look's like, you want to go back to Original FW from E2.This what you have to do,turn Reciver off from the back,hold +button on front of Reciver turn on from back,keep holding + button.Display show's booting then VFD ready,after that the IP Address,it will take wile to come up,so don't let go to early.Use leatest Azup to connect to your Azbox.Format USB Stick whit latest OFW rename it just Patch,inserted in your Reciver.Get E2 Patch named return to OFW,and loaded with Azup.After the Reciver rebooted the display on you TV show's boot from USB.Format Application Aerea first.Hope that Helps.
 

auxius

Registered
Messages
130
Can someone help me how to prevent this error? is causing this the type of TTL cable i use? or the operating system? im using


Quote:
xosPe0 serial#c9d980e5d371a956785968997944df35 subid 0x50
xenv cs2 ok
xosPe0 serial#c9d980e5d371a956785968997944df35 subid 0x50
xenv cs2 ok
xosPe0 serial#c9d980e5d371a956785968997944df35 subid 0x50
xenv cs2 ok
power supply: ok
dram0 ok (9)
dram1 ok (a)
zboot (0) ok
>
**************************************
* SMP863x zboot start ...
* Version: 2.4.0-2.8.0.1
* Started at 0x91000000.
* Configurations (chip revision: 6):
* Use 8KB DRAM as stack.
* Support XLoad format.
* Enabled BIST mode.
* Enabled memory test mode.
* Use internal memory for stage0/1.
**************************************
Boot from flash (0x48000000) mapped to 0x8c000000.
Found XENV block at 0x8c000000.
CPU clock frequency: 300.37MHz.
System clock frequency: 200.25MHz.
DRAM0 dunit_cfg/delay0_ctrl (0xf34111ba/0x000a7888).
DRAM1 dunit_cfg/delay0_ctrl (0xf34111ba/0x00098887).
Using UART port 0 as console.
Board ID.: "852-E2"
Chip Revision: 0x8634:0x86 .. Matched.
Setting up H/W from XENV block at 0x8c000000.
Setting <SYSCLK avclk_mux> to 0x00000000.
Setting <SYSCLK hostclk_mux> to 0x00000100.
Setting <IRQ rise edge trigger lo> to 0xff28ca00.
Setting <IRQ fall edge trigger lo> to 0x0000c000.
Setting <IRQ rise edge trigger hi> to 0x0000009f.
Setting <IRQ fall edge trigger hi> to 0x00000000.
Setting <IRQ GPIO map> to 0x20090820.
Setting <PB default timing> to 0x10101010.
Setting <PB timing0> to 0x10101010.
Setting <PB Use timing0> to 0x000003f4.
Setting <PB timing1> to 0x00110101.
Setting <PB Use timing1> to 0x000003f3.
Setting <PB timing2> to 0x105f1010.
Setting <PB Use timing2> to 0x000003f8.
PB cs config: 0x000e0040 (use 0x000e0040)
Enabled Devices: 0x00021ace
BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD
MAC: 00:02:14:19:a4:f3
PCI IRQ routing:
IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
IDSEL 3: INTA(#15) INTB(#15) INTC(#15) INTD(#15)
Smartcard pin assignments:
OFF pin = 0
5V pin = 1
CMD pin = 2
Setting up Clean Divider 2 to 96000000Hz.
Setting up Clean Divider 4 to 33333333Hz.
Setting up Clean Divider 5 to 25000000Hz.
Setting up Clean Divider 6 to 20000000Hz.
Setting up Clean Divider 7 to 20000000Hz.
GPIO dir/data = 0x76000038/0x76000000
UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
UART1 GPIO mode/dir/data = 0x6e/0x00/0x00
XENV block processing completed.
Found existing memcfg: DRAM0(0x08000000), DRAM1(0x08000000)
Heap/Temp/Temp1/Dest start at 0x14000000/0x16000000/0x15000000/0x12000000.
Default boot index: 0
Scanning ROMFS image at 0x8c040000 (0x48040000) .. Found.
ROMFS found at 0x8c040000, Volume name = YAMON_XRPC
Found 1 file(s) to be processed in ROMFS.
Processing xrpc_xload_yamon_ES4_prod.bin (start: 0x8c040090, size: 0x0002fe84)
Checking zboot file signature .. Not found.
Trying xrpc_xload format .. OK
Checking zboot file signature at 0x13000000 .. OK
Decompressing to 0x91200000 .. OK (453328/0x6ead0).
Load time total 173/255 msec.
Execute final at 0x91200000 ..



**********************************
* YAMON ROM Monitor
* Revision 02.06-SIGMADESIGNS-01-2.8.0.1
**********************************
Memory: code: 0x11000000-0x11040000, 0x11200000-0x11204000
reserved data: 0x11240000-0x12440000, PCI memory: 0x12440000-0x12840000
Environment variable 'start' exists. After 1 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.

xrpc failed (9)--- if a xtask is using a cipher or if you reboot
--- xrpc will fail with RM_BUSY
Checking zboot signature.. it's not zboot file.
Error : Internal, code = ffffffff
YAMON>
 

auxius

Registered
Messages
130
Problem Solve. My newly arrived Yamon prolific PL2303HX TTL to USB solve the problem. Good thing about this is it works on Win7.

Thank you thank you thank you.
 

rastrella

Registered
Messages
2
Hi guys, can someone help me with my azbox blocked on booting? I've made all the procedure using YAMON but after "net init" command everything is locked...

This is what the console shows:

YAMON> net init
Ethernet driver for EM86XX (v1.0)
(MAC 00:02:14:18:2d:fb, tx_desc/rx_desc = 16/32)



Any suggest?
 

gorski

Registered
Messages
1,553
Install PBNIGMA (you have my guide) and then MENU button (you silly!!! :D ) > Plugins > green button (Download plugins) :D...

Really silly, since you do have my guide here... :D

CamD's (Softcams) > MENU > Plugins > External > EXIT button > back to Plugins > CamD's/Softcams > download CCcam, OSCam Emu, MGcamD etc. etc.

Jeezussss... :D
 

hammer15

Registered
Messages
39
Gorski,
I cannot find where your guide is(I have read this thread all the way through and I am worn out).
 

installer2009

Registered
Messages
5
oh dear, I dug out an old azbox premium + HD yesterday with the intention of using it instead of my old dm500 clone, after failing to install oscam I decided I would flash from openRSI 3.0 back to openRSI 2.1 using AZup 2.2.7, needless to say it didn't go to plan and now all I have is booting on vfd do I have to go down the route of serial-ttl cable or is there anything else I can do.
I know these questions have been asked a hundred times and I have read through varios forums and just want to check before I plunge head first into something that I don't really have much of a clue about.
Regards..
Installer.
 

installer2009

Registered
Messages
5
ya kinda figured as much... ok ill order up the cable next week and report back, and the good news is for anyone else that comes across this thread and has the same problem, if I manage to do it, anyone can...
 

Darby

Registered
Messages
8
ciao I have the azbox in booting ...
questo è il log di putty
xosPe0 serial#2f4c1a4351a8c054e8e1042bcad456a1 subid 0x50
xenvàxosPe0 serial#2f4c1a4351a8c054e8e1042bcad456a1 subid 0x50
xenv cs2 ok
power supply: failed
dram0 ok (7)
dram1 ok (8)
zboot (0) ok
>
**************************************
* SMP863x zboot start ...
* Version: 2.4.0-2.8.0.1
* Started at 0x91000000.
* Configurations (chip revision: 6):
* Use 8KB DRAM as stack.
* Support XLoad format.
* Enabled BIST mode.
* Enabled memory test mode.
* Use internal memory for stage0/1.
**************************************
Boot from flash (0x48000000) mapped to 0x8c000000.
Found XENV block at 0x8c000000.
CPU clock frequency: 300.37MHz.
System clock frequency: 200.25MHz.
DRAM0 dunit_cfg/delay0_ctrl (0xf34111ba/0x000b7788).
DRAM1 dunit_cfg/delay0_ctrl (0xf34111ba/0x000b7676).
Using UART port 0 as console.
Board ID.: "852-E2"
Chip Revision: 0x8634:0x86 .. Matched.
Setting up H/W from XENV block at 0x8c000000.
Setting <SYSCLK avclk_mux> to 0x00000000.
Setting <SYSCLK hostclk_mux> to 0x00000100.
Setting <IRQ rise edge trigger lo> to 0xff28ca00.
Setting <IRQ fall edge trigger lo> to 0x0000c000.
Setting <IRQ rise edge trigger hi> to 0x0000009f.
Setting <IRQ fall edge trigger hi> to 0x00000000.
Setting <IRQ GPIO map> to 0x20090820.
Setting <PB default timing> to 0x10101010.
Setting <PB timing0> to 0x10101010.
Setting <PB Use timing0> to 0x000003f4.
Setting <PB timing1> to 0x00110101.
Setting <PB Use timing1> to 0x000003f3.
Setting <PB timing2> to 0x105f1010.
Setting <PB Use timing2> to 0x000003f8.
PB cs config: 0x000e0040 (use 0x000e0040)
Enabled Devices: 0x00021ace
BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD
MAC: 00:02:14:18be
PCI IRQ routing:
IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
IDSEL 3: INTA(#15) INTB(#15) INTC(#15) INTD(#15)
Smartcard pin assignments:
OFF pin = 0
5V pin = 1
CMD pin = 2
Setting up Clean Divider 2 to 96000000Hz.
Setting up Clean Divider 4 to 33333333Hz.
Setting up Clean Divider 5 to 25000000Hz.
Setting up Clean Divider 6 to 20000000Hz.
Setting up Clean Divider 7 to 20000000Hz.
GPIO dir/data = 0x76000038/0x76000000
UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
UART1 GPIO mode/dir/data = 0x6e/0x00/0x00
XENV block processing completed.
Found existing memcfg: DRAM0(0x08000000), DRAM1(0x08000000)
Heap/Temp/Temp1/Dest start at 0x14000000/0x16000000/0x15000000/0x12000000.
Default boot index: 0
Scanning ROMFS image at 0x8c040000 (0x48040000) .. Found.
ROMFS found at 0x8c040000, Volume name = YAMON_XRPC
Found 1 file(s) to be processed in ROMFS.
Processing xrpc_xload_yamon_ES4_prod.bin (start: 0x8c040090, size: 0x0002fe84)
Checking zboot file signature .. Not found.
Trying xrpc_xload format .. OK
Checking zboot file signature at 0x13000000 .. OK
Decompressing to 0x91200000 .. OK (453328/0x6ead0).
Load time total 173/255 msec.
Execute final at 0x91200000 ..






**********************************
* YAMON ROM Monitor
* Revision 02.06-SIGMADESIGNS-01-2.8.0.1
**********************************
Memory: code: 0x11000000-0x11040000, 0x11200000-0x11204000
reserved data: 0x11240000-0x12440000, PCI memory: 0x12440000-0x12840000
Environment variable 'start' exists. After 1 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.


ROMFS not found from 0xac080000 to 0xac080100
Checking zboot signature.. it's not zboot file.
Error : Internal, code = ffffffff

mandando i comandi per ripristinare la rete ho le risposte corrette fino a quando non provo ad avviare la rete

setxenv y.gateway 192.168.1.1
Original value: "192.168.1.1", New value: "192.168.1.1"
Updating XENV block at 0x48000000.
.
XENV verification OK.
YAMON> setxenv y.subnetmask 255.255.255.0
Original value: "255.255.255.0", New value: "255.255.255.0"
Updating XENV block at 0x48000000.
.
XENV verification OK.
YAMON> setxenv y.ipaddr 192.168.1.101
Original value: "192.168.1.101", New value: "192.168.1.101"
Updating XENV block at 0x48000000.
.
XENV verification OK.
YAMON>

Just send net init azbox crashes
Ethernet driver for EM86XX (v1.0)(MAC 00:02:14:18be, tx_desc/rx_desc = 16/32)


thanks
 
Top